Bedienungsanleitung Metabo UHE 26 Multi (Seite 14 von 92) (Alle Sprachen)

625621

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

ENG

Removing the tool:

Turn tool lock (3) in direction indicated by arrow (a)

and remove the tool (b).

8.8 Tool change with keyless chuck

Use the keyless chuck when non-impact drilling in

metal, wood etc. and driving screws.

Chucking the tool:

Turn sleeve towards UP, OPEN" (a). Insert tool as

deeply as possible (b) and turn sleeve in the

opposite direction, until the noticeable mechanical

resistance is overcome.

Caution! The tool is not

yet clamped!

Keep turning the sleeve

(it must "click" when

turning)

until it cannot be turned any further -

only

now

is the tool

securely

clamped.

With a soft tool shank, retightening may be

required after a short time of drilling.

Removing the tool:

Turn sleeve towards UP, OPEN" and remove the

tool (4).

Note:

The ratchet sound which can possibly be

heard after opening the drill chuck, is functional

and is switched off by a reverse rotation of the

sleeve.

If the chuck is extremely tightened:

Unplug. Hold drill chuck with an open end spanner

at the flats on its head and turn the sleeve (4) hard

towards "AUF, RELEASE".

Only moderate pressure is required for hammer

drilling and chiselling. Exerting a high force does

not increase performance.

When drilling deep holes, remove the drill bit

periodically from the hole to release the stone

dust.

Drill tiles and other brittle materials without impact.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with

the opening down, and fully open and close it

several times. The dust collected falls from the

opening. The application of cleaning spray to the

jaws and jaw openings at regular intervals is

recommended.

The vent slots of the machine should be cleaned

from time to time.

If the trigger (12) can not be depressed, check to

see that the direction of rotation selector switch

(10) is fully set to the R or L position.

Electronic signal indicator (9) with VTC

electronics

Rapid flashing - restart protection

(UHE 26 Multi, UHE 28 Multi)

When power is restored after a power supply

failure, for reasons of safety the still switched-on

machine will not start. To continue operation

switch the machine off, then on again.

Slow flashing - carbon brushes worn

(UHE 26 Multi, UHE 28 Multi)

The carbon brushes are almost completely worn.

If the brushes are completely worn, the machine

switches off automatically. Have the brushes

replaced by an authorized service centre.

LED on permanently - overload (UHE 28 Multi)

The motor temperature is too high. Relieve the

machine of the overload condition. If the overload

condition continues, the machine will stop. Switch

the machine off and on again, then let it cool down

at no-load running.

Use only genuine Metabo accessories.

If you need accessories, check with your dealer.

For the dealer to select the correct accessory, he

needs to know the exact model designation of

your power tool.

9Tips and Tricks

10 Maintenance

11 Trouble Shooting

12 Accessories

17026949_0610 UHE 28 UHE 26 UHE 22 Multi.book Seite 14 Donnerstag, 10. Juni 2010 1:07 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo UHE 26 Multi Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info