511040
16
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
16
ENGLISH
ENG
6 Upon attainment of a high torque the motor
comes to a standstill.
8.13 Removing the drill chuck
Keyless chuck Futuro Top (3)
Remove the chuck with two open end spanners.
Keyless chuck Futuro Plus (2)
Remove locking screw. Caution: left-handed
thread!
Hold machine spindle with an open end spanner.
With a rubber mallet tap lightly on a chucked Allen
key to loosen the chuck.
Geared chuck (1)
Remove locking screw. Caution: left-handed
thread!
Hold machine spindle with an open end spanner.
Loosen chuck by lightly tapping on the inserted key
with a rubber mallet, then remove fully.
When drillling deep holes, pull the drill bit out of the
hole from time to time to clear the stone dust or
chips.
Drill tiles and other brittle materials without impact.
To start drilling without centering, activate the
impulse mode (SBE 85, SBE 850 Impuls).
For screw driving the drill chuck can be removed.
Insert screwdriver bit directly into the spindle's
hexagon socket.
Attach the screwdriver-bit retaining bush to hold the
screwdriver bit.
For tapping (not SB 660), apply a little cutting oil to
the tap. Select a low speed and .Set for
clockwise rotation and tap hole, stop machine and
switch to counter-clockwise rotation to remove tap.
Keyless chuck cleaning:
After prolonged use hold the chuck vertically, with
the opening down, and fully open and close it
several times. The dust collected falls from the
opening. The application of cleaning spray to the
jaws and jaw openings at regular intervals is
recommended.
If the trigger (13) can not be depressed, check to
see that the rotation selector switch (14) is fully set
to position R or L (not SB 660).
SBE 85, SBE 850 Impuls: When the machine is
switched on, if the thumb-wheel (9) is turned from
pulse function to torque control, the machine will
switch off automatically. Switch the machine off
and then back on again.
9Tips and Tricks
10 Maintenance
11 Trouble Shooting
17026951_0709 SB_Bauk.book Seite 16 Montag, 13. Juli 2009 1:54 13
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo UT 3000 E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info