Bedienungsanleitung Metabo W 18 LTX 150 Quick (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595439

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISHen

7.3 Securing/releasing the (tool-free)

clamping nut (depending on features)

Only tighten the (tool-free) clamping nut (2)

manually.

For the machine to operate, the clip (1) must

always lie flat on

clamping nut (2)

To secure the (tool-free) clamping nut (2):

Do not use the

(tool-free) clamping nut if the

accessory has a clamping shank thicker than 6

! In this case, use the

clamping nut (17) with 2-

hole spanner (18).

- Lock the spindle (see chapter 7.1).

- Flip up the clip

(1)

on the clamping nut.

-Fit the clamping nut (2) on the spindle (4). See

illustration on page 2.

(1)Tighten the

clamping nut on the clip manually

in a clockwise direction.

- Flip down the clip

(1) again

To release the (tool-free) clamping nut (2)

- Lock the spindle (see chapter 7.1).

- Flip up the clip

(1)

on the clamping nut.

- Unscrew the clamping nut

(2)

, turning it

anticlockwise manually .

Note: If the clamping nut is very tightly secured

(2),

you can also use a 2-hole spanner

to unscrew it.

7.4 Securing/releasing the clamping nut

(depending on features)

Securing the clamping nut (17):



The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration D on page 2.

- A) For thin grinding wheels: 

The edge of the clamping nut (17) faces upwards

so that the thin grinding wheel can be attached

securely.



B) For thick grinding wheels: 

The edge of the clamping nut (17) faces

downwards so that the clamping nut can be

attached securely to the spindle.

- Lock the spindle. Turn the clamping nut (17)

clockwise using the 2-hole spanner (18) to

secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (17) anticlockwise using the 2-hole

spanner (18) to unscrew.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid switching on the machine accidentally:

always switch it off when the battery pack is

removed from the machine.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

Machines with slide switch:

Switching on: Push the slide switch (6) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (6) and release.

Machines with Paddle Switch 

(with dead man function):

(machines with the designation WP...)

Switching on: Slide the switch-on lock (13) in 

the direction of the arrow and press 

the trigger (14).

Switching off: Release the trigger (14).

8.2 Working instructions

Grinding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.



Roughing: position the machine at an angle of 30° -

40° for the best working results.

Cutting-off:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Sanding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Wire brushing:

Press down the machine evenly.

Clean the dust filter regularly: remove and clean

with a jet of compressed air.

8. Use

9. Cleaning

14 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo W 18 LTX 150 Quick Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info