Bedienungsanleitung Metabo W 2000 (Seite 15 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599583

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH en

2Spindle

3 Spindle locking button

4 Lock (to prevent the machine from being switched

on unintentionally, or for continuous operation)*

5 Trigger (

for switching on and off)

6 Additional handle

7 Safety guard

8 Clamping nut

92-hole spanner

10 Screw (for adjusting and securing the

safety guard)

* depending on equipment/not in scope of delivery

Before plugging in, check to see that the rated

mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Australia: Always use a residual current device

(RCD) protected supply with a rated residual

current of 30 mA or less.

Always use an extension cable with a minimum

diameter of 1.5 mm

. The extension cable must be

suitable for the machine power rating (see

Technical Specifications). If using a roll of cable,

always roll up the cable completely.

6.1 Attaching the additional handle

Always work with the additional handle

attached (6)! Manually screw in the additional

handle securely in the left, centre or right threaded

hole (depending on requirements).

6.2 Attaching the safety guard

(for work involving grinding wheels)

Prior to commissioning: Fit the

protective cover.

For reasons of safety, the safety guard (7)

should always be attached when roughing

work is performed.

For reasons of safety, the special parting

guard should always be attached before

parting work is performed (see chapter 11.

Accessories).

See illustration D/E on page 2.

- Slacken the screw (10). Place the safety guard (7)

in the position indicated.

- Turn the safety guard until the closed section is

facing the operator.

- Tighten the screw (10), ensuring that the anti-twist

device engages in the slots.

- Make sure that the guard is seated securely: you

should not be able to turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

6.3 Power supply

The mains sockets must be protected using time-

delay fuses or circuit breakers.

Machines with "X" in the model designation:

(with integrated, automatic restriction of the starting

current (soft start)). The mains sockets can also be

protected using fast-acting fuses or circuit breakers.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (3) only

when the spindle is stationary!

- Press in the spindle locking button (3) and turn the

spindle

(2) by hand until you feel the spindle locking

button engage.

7.2 Placing the grinding wheel in position

See illustration B on page 2.

- Fit the support flange (1) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Position the grinding wheel on the support flange

(1) as shown in illustration B.

The grinding wheel must lay flat on the supporting

flange. The metal flange on the parting grinder

disc must lay flat on the support flange.

7.3 Securing/Releasing the clamping nut

Securing the clamping nut (8):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration C on page 2.

- A) For thin grinding wheels:

The edge of the clamping nut (8) faces upwards

so that the thin grinding wheel can be attached

securely.

B) For thick grinding wheels:

The edge of the clamping nut (8) faces

downwards so that the clamping nut can be

attached securely to the spindle.

- Lock the spindle. Turn the clamping nut (8)

clockwise using the 2-hole spanner (9) to secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (8) anticlockwise using the 2-hole

spanner (9) to unscrew.

6. Commissioning

7. Attaching the grinding wheel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo W 2000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info