Bedienungsanleitung Metabo W 22-230 MVT (Seite 16 von 121) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599580

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

ENGLISHen

See page 2.

1"Quick"clamping nut *

2Support flange *

3Spindle

4WE

...: Autobalancer support flange (non-

detachable) *

5 Spindle locking button

6 Electronic signal indicator *

7 Lock (to prevent the machine from being

switched on unintentionally, or for continuous

operation)*

8 Trigger (for switching on and off)

9 Button (to turn the main handle)

10 Main handle

11 Additional handle/Additional handle with

vibration damping

12 Safety cover

13 Adjusting nut *

14 2-hole spanner *

15 Quick-release clamp (to adjust safety guard

without the use of tools)

16 Screw (to adjust clamping force of quick-

release clamp)

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

Use only extension cables with a min. cross-section

of 1.5 mm

. Extension cables must correspond to

the power consumption of the machine (cf

Technical Specifications). If a cable roller is used,

always roll up the cable completely.

6.1 Attaching the additional handle

Always work with the additional handle (11)

attached! Manually screw in the additional

handle securely in the left, centre or right threaded

hole (depending on requirements).

6.2 Attach the safety guard

(for working with abrasive discs)

Prior to operation: Attach safety

guard.

For reasons of safety, the safety guard (12)

should always be attached when roughing

work is performed.

For reasons of safety, the special parting

guard should always be attached before

parting work is performed (see chapter 11.

Accessories).

See illustration E on page 2.

- Open quick-release clamp (15). Mount the safety

guard (12) in the position indicated.

- Turn the safety guard until the closed section is

facing the operator.

- Close quick-release clamp.

- If necessary, increase clamping force of quick-

release clamp by tightening the screw (16) (with

opened quick-release clamp).

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

6.3 Pivotable main handle

Only work with the main handle (10) engaged.

See illustration B on page 2.

- Push in the button (9).

- The main handle (10) can now be turned 90° to

both sides and can be engaged.

- Make sure that it is securely positioned: the main

handle (10) must be engaged and it should not be

possible to move it.

6.4 Power-supply connection

The mains sockets must be protected using time-

delay fuses or circuit breakers.

Machines with "WE..." in the model designation:

(with inbuilt automatic startup-current limitation(soft

start).) The mains sockets can also be protected

using fast-acting fuses or circuit breakers.

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (5) only

when the spindle is stationary!

- Press in the spindle locking button (5) and

turn the spindle (3) by hand until the spindle

locking button engages.

7.2 Placing the grinding wheel in position

See illustration C on page 2.

Machines with the designation W 2..., WE 2...:

- Fit the support flange (2) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Position the grinding wheel on the support flange

(2) as shown in illustration C.

The grinding disc must lay flat on the supporting

flange.

Machines with the designation WEA 2...:

The Autobalancer support flange (4) is

permanently fitted on the spindle. As is the

case with most other angle grinders, a detachable

support flange is not necessary.

5. Overview

6. Commissioning

7. Attaching the grinding disc

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo W 22-230 MVT Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info