Bedienungsanleitung Metabo W 24-180 (Seite 15 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599596

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH en

See page 2.

1 "Quick"clamping nut *

2 Support flange

3Spindle

4 Spindle locking button

5 Electronic signal indicator*

6 Lock (to prevent the machine from being switched

on unintentionally, or for continuous operation)*

7 Trigger (

for switching on and off)

8 Button (to turn the main handle)*

9 Main handle

10 Additional handle / Additional handle with vibration

damping *

11 Safety guard

12 Clamping nut *

13 2-hole spanner *

14 Lever (to adjust safety guard without the use of

tools)

* depending on equipment/not in scope of delivery

If delivered without a mains plug, arrange for a

suitable mains plug to be connected by a

qualified electrician ONLY.

Before plugging in, check to see that the rated

mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

Always use an extension cable with a minimum

diameter of 1.5 mm

. The extension cable must be

suitable for the machine power rating (see

Technical Specifications). If using a roll of cable,

always roll up the cable completely.

6.1 Attaching the additional handle

Always work with the additional handle

attached (10)! Manually screw in the

additional handle securely in the left, centre or right

threaded hole (depending on requirements).

6.2 Attaching the safety guard

(for work involving grinding wheels)

Prior to commissioning: Fit the

protective cover.

For reasons of safety, the safety guard (11)

should always be attached when roughing

work is performed.

For reasons of safety, the special parting

guard should always be attached before

parting work is performed (see chapter 11.

Accessories).

See illustration E on page 2.

- Push and hold the lever (14). Place the safety

guard (11) in the position indicated.

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is seated securely: the

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

6.3 Rotatable main handle (depending on

features)

Only work with the main handle (9) engaged.

See illustration B on page 2.

- Push in the button (8).

- The main handle (9) can now be turned 90° to both

sides and can be engaged.

- Make sure that it is securely positioned: the main

handle (9) must be engaged and it should not be

possible to move it.

6.4 Power supply

The mains sockets must be protected using time-

delay fuses or circuit breakers.

Machines with "X" in the model designation:

(with integrated, automatic restriction of the starting

current (soft start)). The mains sockets can also be

protected using fast-acting fuses or circuit breakers.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (4) only

when the spindle is stationary!

- Press in the spindle locking button (4) and turn the

spindle

(3) by hand until you feel the spindle locking

button engage.

7.2 Placing the grinding wheel in position

See illustration C on page 2.

- Fit the support flange (2) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Position the grinding wheel on the support flange

(2) as shown in illustration C.

The grinding wheel must lay flat on the supporting

flange. The metal flange on the parting grinder

disc must lay flat on the support flange.

7.3 Securing/Releasing the "Quick"clamping

nut (depending on features)

Securing the "Quick"clamping nut (1):

5. Overview

6. Commissioning

7. Attaching the grinding wheel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo W 24-180 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info