Bedienungsanleitung Metabo W 9-100 (Seite 19 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595481

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH en

Releasing the clamping nut (1):

Only when the "Quick" clamping nut (1) is

attached must the spindle be stopped using

the red M-Quick spindle locking button! (4)

- The machine continues to run after switching off.

- Press in the M-Quick spindle locking button just

before the grinding disc stops. (4) The "Quick"

clamping nut (1)loosens itself by around half a turn

and can be removed without additional effort or

tools.

7.4 Securing/Releasing the 2-hole nut

(depending on features)

Securing the 2-hole nut (13):

The 2 sides of the 2-hole nut are different. Screw the

2-hole nut onto the spindle as follows:

See illustration B on page 2.

- X) For thin grinding discs:

The edge of the 2-hole nut (13) faces upwards so

that the thin grinding disc can be attached

securely.

Y) For thick grinding discs:

The edge of the 2-hole nut (13) faces downwards

so that the 2-hole nut can be attached securely to

the spindle.

Z) Only for W 9-100:

The collar of the 2-hole nut faces downwards and/

or the flat surface faces upwards.

- Locking the spindle. Turn the 2-hole nut

(13)clockwise using the 2-hole spanner (14) to

secure.

Releasing the 2-hole nut:

- Lock the spindle (see chapter 7.1). Turn the 2-hole

nut (13) anticlockwise using the 2-hole spanner

(14) to unscrew.

8.1 Adjusting the speed (depending on

features)

Set the recommended speed at the thumbwheel.

(8) (small number = low speed; large number = high

speed)

Cutting disc, roughing disc, cup wheel and diamond

cutting disc: high speed

Brush: medium speed

Sanding plate: low to medium speed

Note:

We recommend using our angle polisher for

polishing work.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

Machines with slide switch:

Switching on: Push the sliding switch forward. (5)

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (5) and release it.

Machines with paddle switch

(with dead man function):

Switching on: Slide the switch-on lock (10) in the

direction of the arrow and press the trigger

(9).

Switching off: Release the trigger switch. (9)

8.3 Working Directions

Grinding and sanding operations:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Rough grinding: position the machine at an angle of

30° - 40° for the best working results.

Cutting-off operations:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Wire brushing:

Press down the machine evenly.

8.4 Rotate gear housing

See illustration D on page 3.

- Disconnect from the power supply.

- Unscrew the fastening screw (a) of the lever (15).

Remove the screw, lever (with its sheet metal part)

and put aside.

- Unscrew the 4 gear housing screws (b).

CAUTION! Do not remove the gear housing!

- Turn the gear housing to the desired position

without removing it.

- Screw in the 4 gear housing screws (b) in the

available threads! Tightening torque = 3.0 Nm +/-

0.3 Nm.

8. Use

88 989

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo W 9-100 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info