ENGLISHen
10
The pump can be switched on/off in "Mode A"
using the button (
also the same as in normal mode.
Automatic domestic water system
(device designation HWA...)
Functional principle: The d
the removal of water causes
fall below the switch-on pres
again when switch-off pressure is reac
1. Insert mains plug.
2. Fill pump if n
3. Switch on the device -
4. Open the discharge line (open
spray nozzle)
5. Check that wate
ready for operation.
Domestic water system
(device designation HWW...)
Functional principle: The d
the removal of water causes
fall below the switch-on pres
again when switch-off pressure is reached. The
pressure vessel contai
is under air pressure (pilot pres
ered; this permits the removal of small
water without the pump starting
1. Insert mains plug.
2. Fill pump if n
3. Switch on the device -
4. Open the discharge line (open
spray nozzle)
5. Check that wate
ready for operation.
Danger! Prior to all ser
-U
- Ensure that the device and connected accesso-
ries are depressuri
- Repair and maintenance work ot
described in th
out by qualified
8.1 Regular maintenance
- Check device and acces
electrical and pressurised components, for
damage and repair if necessary.
- Check suction and di
- If the conveying capacity decreases, clean intake
filter and filter
necessary.
- Check the pilot pressure of the pressure vessel
(7) (depending on features) and increase it if
necessary (seI
sure).
8.2 Cleaning the intake filter
features)
1. Unscrew the cover (1
sary (15)).
2. Pull the filter unit (17) upwards vertically to
remove.
3. Disassemble the filter unit: Hold the cup (18),
turn the filter (19) in a clockwise direction and
remove it from the cup (bayonet lock).
4. Place the cup (18) under flowing water to clean
and use a soft brush to clean the filter (19).
5. Assemble again in reverse order. I
ensure that the filter unit (17) is fully inserted.
8.3 Danger of frost
Caution! Frost (< 4 °C) des
and accessories as both always contain
water!
- If there is a danger of frost, disassemble pump
and accessor
tions (see following section).
8.4 Removing and storing device
- Switch off appliance. Unplug
- Open the discharge line
nozzle), allow
- Completely drain the
- unscrewing the water drain screw (9).
- Remove suction and discharge lines
device.
- Store device in a frost-free room (min. 5 °C).
f
Danger!
- Prior to all servic
- Unplug main
- Ensure that the device and connected accesso-
ries are depressurised.
9.1 Pump is not running
• No
- Cbles, plug, socket and
mains fuse.
• Mains vo
- Use an extension cable with sufficient
conductor diame
• Motor over
tripped.
- After cooling the p
- Guarantee sufficient ventilation, keep air slots
free.
- Observe maximum supply temperature.
• Motor hums, but does not start.
- With the motor switched off, insert a screw-
driver or similar
the motor and turn the fan impeller.
• Pump
- Disassemble and c
replace if nec
if necessar
9.2 Pump not drawing in correctly or run-
ning very loudly:
• I
- E
• Pump not y filled with water.
-S
• Sucti
- Seal suction line, tighten scre
• Sucti
- Observe maximum suction height.
- Insert check valve, fill suction line with wa
• Intake filter (accessories) obstructed.
- C
• Check valve (accessor
- C
• Water discharge between motor and pump,
shaft seal leaking. (Minor dis
(max. approx. 30 drops per day) is normal with
the use of shaft seals).
- Replace shaft seal. See secti
• Pump
-S
9.3 Pressure too low or pump runs cont
ously:
• Sucti
-S
• Pump
-S
• HWW...: Pressure switch incorrectly adjusted.
- Read off switch-on and switch-o
the pressure gauge (11) and check values
(see section 13 Technical Specification
an adjustment i
Metabo Custoice. See section 11.
• HWW...:
small volume of wa
- C
sure vessel is too low. Inc
necessary. See section
• HWW...: Water is running out of the air valve.
- Rubber bellows in pressure vessel leaking,
replace it. See section 11.
• P 6000 Inox: The LED
- "Mode A" is enabled. See section 7.2
9.4 Increasing pilot pressure (only HWW...)
If – in the course of time – the
after the removal of a small volume
(approx. 0.5 l), the p
be restored.
Note:
The pilot pressure cannot be read
pressure gauge (11).
1. Unplug mains cable.
2. Open the discharge line (open water tap or
spray nozzle),
completely.
3. Unscrew plastic front face of pressure
vessel; the air valve is located behind it.
4. Mount air pump or co
"tyre valve" connection and pressure gauge on
the air valve.
5. Pump up to the specified pilot pressure (see
section 13. Techn
6. Connect device again and check operation.
f
Use only genuine Metabo accessories.
Use only accessories that fulfil the req
and specificatin these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Danger! Repairs to this device must be
carried out by qua
If you have Metabo devices that require repairs,
please contact your
addresses see www.metabo.com.
For shipment: drain pump and ves
(see section 8.4).
You can downloa
www.metabo.com.
Observe national
compatible disp
disused machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric
and its implementation in national l
used power tools must be collected separately and
handed in for
cling.
Explanatory notes on
Subject to change in line with technological
advances.
The pump characteristic cur
3) shows the conveying capacity that can be
reached depen
(suction hei
V =
suction connectio
K =
U=
f=
P
1
=R
I=
C =
n=
F
V,max
=
F
h,max
=
F
p,max
=
p
1
=
p
2
=
S
h,max
=
S
temp
=M
T
temp
=A
S
1
=
S
2
=
S
3
=
M
P
=
M
R
=
M
W
=
D
s
=
D
p
=
T
V
=
T
p,max
=
T
p,1
=
A =
Length x Width x Height
m =
~ Alternating current
The technical quoted are subject to
tolerances (in co
standards).
Emission values
8. Maintenance
9. Troubleshooting
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications
