Bedienungsanleitung Metabo WB 11-150 Quick (Seite 14 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

665554

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISHen

8 Additional handle / Additional handle with vibration

damping *

9 Safety guard for grinding

10 Support flange *

11 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in the device, check to see

that the rated mains voltage and mains

frequency, as specified on the rating label, match

your power supply.

6.1 Attaching the additional handle

Always work with the additional handle

attached (8)! Attach the additional handle on

the left or right of the machine and secure.

6.2 Install safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter 11.

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See illustration E on page 2.

- Push and hold the lever (11). Place the safety

guard (9) in the position indicated.

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is seated securely: the

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

- Press in the spindle locking button (4) and turn the

spindle (2) by hand until you feel the spindle

locking button engage.

7.2 Placing the grinding wheel in position

WBA..., WEBA..., WEPBA...:

See illustration C on page 2.

The Autobalancer support flange (3) is perma-

nently fitted on the spindle. As is the case with

most other angle grinders, a detachable support

flange is not necessary.

The contact surfaces of the Autobalancer

support flange (3), grinding wheel and the

"Quick" clamping nut (1) must be clean. Clean if

necessary.

- Place the grinding wheel on the Autobalancer

support flange (3).

The grinding wheel must lie flat on the Auto-

balancer supporting flange. The metal flange on

the parting grinder discs must lie flat on the Auto-

balancer support flange.

WB 11-125 Quick, WB 11-150 Quick:

See illustration D on page 2.

- Fit the support flange (10) on the spindle. The

flange should not turn on the spindle when prop-

erly attached.

- Place the grinding wheel on the support flange

(10). The grinding wheel must lay flat on the

supporting flange. The metal flange on the parting

grinder disc must lay flat on the support flange.

7.3 Tightening/loosening the "Quick" clamp-

ing nut

Securing the "Quick"clamping nut (1):

Do not use the "Quick" clamping nut

if the acces-

sory has a clamping shank thicker than 8mm

- Lock the spindle (see chapter 7.1).

- Position the "Quick"clamping nut (1) on the

spindle (2) so that the 2 lugs engage in the 2

grooves on the spindle. See illustration on page 3.

- Tighten the "Quick"clamping nut by turning clock-

wise by hand.

-Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

Releasing the "Quick"clamping nut (1)

The "Quick"clamping nut (1) must be attached

before the spindle locking button (4) can hold

the spindle!

- The machine continues to run after switching off.

- Press in the spindle locking button (4) just before

the grinding wheel stops. The "Quick"clamping

nut (1) is released.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

6. Initial Operation

7. Attaching the grinding wheel

8. Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WB 11-150 Quick Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info