Bedienungsanleitung Metabo WE 22-230 MVT (Seite 17 von 121) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599578

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

ENGLISH en

The contact surfaces of the Autobalancer

support flange (4), grinding wheel and the

Quick-Stop adjusting nut (1) or other adjusting nut

(13) must be clean. Clean if necessary.

- Place the grinding wheel on the Autobalancer

support flange (4). The grinding wheel must lie flat

on the Autobalancer supporting flange.

7.3 Securing/Releasing the "Quick"

clamping nut (depending on features)

Securing the "Quick" clamping nut (1):

Do not use the "Quick" clamping nut if the

accessory has a clamping shank thicker than 8

mm! In this case, use the clamping nut (13) with 2-

hole spanner (14).

Only use the "Quick" clamping nut when

undamaged and in perfect operating

condition: the arrow must point to the notch on the

outer ring (see illustration on page 2).

- Lock the spindle (see chapter 7.1).

- Fit the "Quick" clamping nut (1) on the spindle (3).

See illustration on page 2.

- Tighten the "Quick"clamping nut by turning

clockwise by hand.

- Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

Releasing the clamping nut (1):

- Lock the spindle (see chapter 7.1).

- Turn the "Quick"clamping nut (1) anticlockwise to

unscrew.

7.4 Securing/Releasing the clamping nut

(depending on features)

Securing the clamping nut (13):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration D on page 2.

- A) For thin grinding discs:

The edge of the clamping nut (13) faces upwards

so that the thin grinding disc can be attached

securely.

B) For thick grinding discs:

The edge of the clamping (13) faces downwards

so that the 2-hole nut can be attached securely to

the spindle.

- Locking the spindle. Turn the clamping nut (13)

clockwise using the 2-hole spanner (14) to secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (13) anticlockwise using the 2-hole

spanner (14) to unscrew.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand

securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

See illustration A on page 2.

Torque activation

Switching on:

Slide the lock (7) in the direction of the

arrow and press the trigger switch (8).

Switching off:

Release the trigger switch (8).

Continuous operation (depending on features)

Switching on:

Slide the lock (7) in the direction of the

arrow, press the trigger switch (8) and keep

it pressed. The machine is now switched on.

Now slide the lock (7) in the direction of the

arrow once more to lock the trigger switch (8)

(continuous operation).

Switching off:

Press the trigger switch (8) and

release.

8.2 Working Directions

Grinding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Rough grinding: position the machine at an angle of

30° - 40° for the best working results.

Cutting-off operations:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Sanding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Wire brushing:

Press down the machine evenly.

Cleaning the motor: It is possible

that particles deposit inside the

power tool during operation. This impairs the

cooling of the power tool. Conductive build-up can

impair the protective insulation of the power tool and

cause electrical hazards.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

8. Use

9. Cleaning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WE 22-230 MVT Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info