Bedienungsanleitung Metabo WE Partner Edition (Seite 15 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

665546

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH en

See page 2.

1 "Quick" clamping nut *

2 Support flange

3Spindle

4 Spindle locking button

5 Sliding

on/off switch *

6 Electronic signal indicator *

7 Speed adjustment wheel *

8Switch-on lock *

9 Trigger *

10 Additional handle / Additional handle with vibration

damping *

11 Safety cover

12 Clamping nut *

13 2-hole spanner *

14 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check to see that the rated

mains voltage and mains frequency,

as stated on the rating label, match your power

supply.

6.1 Attaching the additional handle

Always work with the additional handle

attached (10)! Attach the additional handle

on the left or right of the machine and secure.

6.2 Install safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter 11.

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See page 2, illustration C.

- Push and hold the lever (14). Place the safety

guard (11) in the position indicated.

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is seated securely: the

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work

(see chapter 11. Accessories).

7.1 Locking the spindle

- Press in the spindle locking button (4) and turn the

spindle (3) by hand until the spindle locking button

engages.

7.2 Placing the grinding wheel in position

See illustration A on page 2.

- Place the supporting flange (2) on the spindle. The

flange should not turn on the spindle when

properly attached.

Only with W 8-100: Screw support flange with two-

pin spanner onto spindle so that the small collar

(with diameter 16 mm) is facing upwards.

Place the grinding wheel on the support flange (2).

The grinding wheel must lay flat on the supporting

flange. The metal flange on the parting grinder

disc must lay flat on the support flange.

7.3 Securing/Releasing the "Quick"

clamping nut (depending on features)

Securing the "Quick" clamping nut (1):

Do not use the

"Quick" clamping nut if the

accessory has a clamping shank thicker than 8

! In this case, use the

clamping nut (12) with 2-

hole spanner (13).

- Lock the spindle (see chapter 7.1).

- Position the "Quick" clamping nut (1) on the

spindle (3) so that the 2 lugs engage in the

2 grooves on the spindle. See illustration on

page 2.

- Tighten the "Quick" clamping nut by turning

clockwise by hand.

- Turn the grinding wheel firmly clockwise to tighten

the "Quick" clamping nut.

Releasing the "Quick" clamping nut (1)

The "Quick" clamping nut (1) must be attached

before the spindle locking button (4) can hold

the spindle!

- The machine continues to run after switching off.

- Press in the spindle locking button (4) just before

the grinding wheel stops. The "Quick" clamping

nut (1) is released.

7.4 Securing/Releasing the clamping nut

(depending on features)

Securing the clamping nut (12):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration B on page 2.

- X) For thin grinding wheels:

The edge of the clamping nut (12) faces upwards

so that the thin grinding wheel can be attached

securely.

Y) For thick grinding wheels:

The edge of the clamping nut (12) faces

5. Overview

6. Commissioning

7. Attaching the grinding wheel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WE Partner Edition Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info