Bedienungsanleitung Metabo WEPBF 15-150 Quick (Seite 15 von 112) (Alle Sprachen)

625648

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH en

and carefully re-enter the cut. The wheel may

bind, walk up or kickback if the power tool is

restarted in the workpiece.

e) Support panels or any oversized workpiece

to minimize the risk of cutting disc pinching

and kickback. Large workpieces tend to sag under

their own weight. Supports must be placed under

the workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

f) Use extra caution when making "pocket cuts"

into existing walls or other blind areas. The

protruding cutting disc may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

4.5 Safety Warnings Specific for Sanding

Operations:

a) Do not use excessively oversized sanding

disc paper. Follow manufacturers

recommendations, when selecting sanding

paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may

cause snagging, tearing of the disc or kickback.

4.6 Safety Warnings Specific for Wire

Brushing Operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

4.7 Additional Safety Instructions:

WARNING – Always wear protective

goggles.

Use elastic cushioning layers if they have been

supplied with the grinding media and if required.

Observe the specifications of the tool or accessory

manufacturer! Protect the discs from grease or

impacts!

Grinding wheels must be stored and handled with

care in accordance with the manufacturer's

instructions.

Never use cutting discs for roughing work! Do not

apply pressure to the side of the cutting discs.

The workpiece must lay flat and be secured against

slipping, e.g. using clamps. Large workpieces must

be sufficiently supported.

If accessories with threaded inserts are used, the

end of the spindle may not touch the base of the

hole on the grinding tool. Make sure that the thread

in the accessory is long enough to accommodate

the full length of the spindle. The thread in the

accessory must match the thread on the spindle.

See page 4 and chapter 14. Technical

Specifications for more information on the spindle

length and thread.

Use of a fixed extractor system is recommended.

Always install an RCD with a maximum trip current

of 30 mA upstream. If the angle grinder is shut down

via the RCD, it must be checked and cleaned. See

chapter 9. Cleaning.

Damaged, eccentric or vibrating tools must not be

used.

Avoid damage to gas or water pipes, electrical

cables and load-bearing walls (static).

Pull the plug out of the socket before making any

adjustments, converting or servicing the machine.

A damaged or cracked side handle must be

replaced. Never operate a machine with a defective

side handle.

A damaged or cracked safety guard must be

replaced. Never operate a machine with a defective

safety guard.

Secure small workpieces. For example, clamp in a

vice.

This power tool is not suitable for polishing work.

Improper use of the machine will void the warranty!

The motor may overheat and damage the electric

power tool. We recommend using our angle

polisher for polishing work.

The accessory may not be fastened with a two-hole

nut for safety reasons. Only use the (tool-free)

clamping nut (2).

Reducing dust exposure:

Some of the particles generated using this

power tool may contain substances known to

cause cancer, allergic reactions, respiratory

diseases, birth defects or other reproductive harm.

Some of these substances include: Lead (in paint

containing lead), mineral dust (from bricks,

concrete etc.), additives used for wood treatment

(chromate, wood preservatives), some wood types

(such as oak or beech dust), metals, asbestos.

The risk from exposure to such substances will

depend on how long the user or nearby persons are

being exposed.

Do not let particles enter the body.

Do the following to reduce exposure to these

substances: Ensure good ventilation of the

workplace and wear appropriate protective

equipment, such as respirators able to filter

microscopically small particles.

Observe the relevant guidelines for your material,

staff, application and place of application (e.g.

occupational health and safety regulations,

disposal).

Collect the generated particles at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work (see

chapter 11.), thus less particles enter the

environment in an uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- Do not direct the escaping particles and the

exhaust air stream at yourself or nearby persons

or on dust deposits.

- Use an extraction unit and/or air purifiers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPBF 15-150 Quick Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info