Bedienungsanleitung Metabo WEPF 15-150 Quick (Seite 13 von 112) (Alle Sprachen)

625647

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH en

Original Instructions

We, being solely responsible: Hereby declare that

these flat head angle grinders, identified by type

and serial number *1), meet all relevant

requirements of directives *2) and standards *3).

Technical documents for *4) - see page 4.

The flat head angle grinders, when fitted with

original Metabo accessories, are suitable for

grinding, sanding, cut-off grinding and wire

brushing metal, concrete, stone and similar

materials without the use of water.

The user bears sole responsibility for any damage

caused by inappropriate use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

For your own protection and for the

protection of your power tool, pay

attention to all parts of the text that are

marked with this symbol!

WARNING – Reading the operating

instructions will reduce the risk of injury.

WARNING Read all safety warnings and

instructions. Failure to follow all safety

warnings and instructions may result in electric

shock, fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Pass on your power tool only together with these

documents.

4.1 General Safety Recommendations

for Grinding, Sanding, Wire Brushing or

Cut-Off Grinding:

Use

a) This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power

tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or serious

injury.

b) Operations such as polishing are not

recommended to be performed with this power

tool. Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

c) Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Grinding accessories running

faster than their rated speed can break and fly apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

f) Threaded mounting of accessories must

match the grinder spindle thread. For

accessories mounted by flanges, the arbour

hole of the accessory must fit the locating

diameter of the flange. Accessories that do not

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

grinding wheels for chips and cracks, backing

pad for cracks, tear or excess wear, wire brush

for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute. Damaged accessories will normally break

apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by

various operations. The dust mask or respirator

must be capable of filtrating particles generated by

your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of

operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory

contacting a "live" wire may make exposed metal

parts of the power tool "live" and shock the operator.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be cut

or snagged and your hand or arm may be pulled into

the spinning accessory.

1. Declaration of Conformity

2. Specified Use

3. General Safety Instructions

4. Special Safety Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPF 15-150 Quick Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info