Bedienungsanleitung Metabo WEPF 9-125 Quick (Seite 18 von 124) (Alle Sprachen)

625650

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISHen

Machines with Paddle Switch (with dead man

function):

(machines with the designation WPF..., WEPF...)

Switching on: Slide the switch-on lock (10) in

the direction of the arrow and press

the trigger (11).

Switching off: Release the trigger (11).

8.2 Working instructions

Grinding and sanding operations:

Press down the machine evenly on the surface and

move back and forth so that the surface of the work-

piece does not become too hot.

Roughing: position the machine at an angle of 30° -

40° for the best working results.

Cutting-off:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed suit-

able for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Wire brushing:

Press down the machine evenly.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

Clean the dust filter regularly: remove and clean

with a jet of compressed air.

10.1 Mains powered machines:

- Overload protection: There is a MAJOR

reduction in load speed. The motor temperature

is too high! Allow the machine to run at idle speed

until it has cooled down.

- Overload protection: There is a SLIGHT

reduction in load speed. The machine is over-

loaded. Reduce the load before continuing to

work.

- Metabo S-automatic safety shutdown: The

machine was SWITCHED OFF automatically. If

the slew rate of the current is too high (for

example, if the machine suddenly seizes or kick-

back occurs), the machine switches off. Switch off

the machine at the slide switch (8). Switch it on

again and continue to work as normal. Try to

prevent the machine from seizing. See section

4.2.

- Restart protection: The machine does not

start. The restart protection is active. If the mains

plug is inserted with the machine switched on, or if

the current supply is restored following an inter-

ruption, the machine does not start up. Switch the

machine off and on again.

10.2 Cordless machines:

- The electronic signal display (12) lights up

and the load speed decreases. The tempera-

ture is too high! Run the machine in idling until the

electronics signal indicator switches off.

- The electronic signal display (12) flashes and

the machine does not start. The restart protec-

tion is active. The machine will not start if the

battery pack is inserted while the machine is on.

Switch the machine off and on again.

Use only genuine Metabo accessories.

See page 4.

Use only accessories that fulfil the requirements

and specifications listed in these operating instruc-

tions.

A Safety guard for cut-off grinding

Designed for work with cut-off wheels, diamond cut-

off wheels.

Install as described under "Safety guard for

grinding" (chapter 6.4).

B Hand guard for sanding and wire brushing

operations

Designed for work with support plates, sanding

pads, wire brushes.

Install hand guard under the additional side-

mounted handle.

CChargers

D Battery packs

For a complete range of accessories, see

www.metabo.com or the accessories catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

The sanding dust generated may contain

hazardous materials: do not dispose of with the

household waste, but at a special collection point

for hazardous waste.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with

European Guideline 2002/96/EC on used electronic

9. Cleaning

10. Troubleshooting

11 10

11. Accessories

12. Repairs

13. Environmental Protection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEPF 9-125 Quick Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info