Bedienungsanleitung Metabo WEV 10-125 Quick (Seite 18 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595487

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISHen

Collect the generated particles at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work (see

chapter 11.), thus less particles enter the

environment in an uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- Do not direct the escaping particles and the

exhaust air stream at yourself or nearby persons

or on dust deposits.

- Use an extraction unit and/or air purifiers

- Ensure good ventilation of the workplace and

keep clean using a vacuum cleaner Sweeping or

blowing stirs up dust

- Vacuum or wash the protective clothing Do not

blow, beat or brush

See page 2.

1"Quick"clamping nut *

2 Support flange

3Spindle

4 Spindle locking button

5 Sliding on/off switch *

6Handle

7 Electronic signal indicator *

8 Thumbwheel for selection of speed *

9 Trigger *

10 Switch-on lock

11 Additional handle/Additional handle with vibration

damping *

12 Safety cover

13 2-hole nut *

14 2-hole spanner *

15 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check to see that the rated

mains voltage and mains frequency, as stated

on the rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle

attached! (11) Attach the additional handle on

the left or right of the machine and secure.

6.2 Attach the safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter11.Accessories!

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See illustration C on page 2.

- Push and hold the lever. (15) Place the safety

guard in the position indicated. (12)

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is placed securely: The

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least 3.4

mm by the safety guard.

(Disassemble in reverse order.)

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the cutting guard

before performing cutting-off operations (see

chapter Accessories).11.

7.1 Locking the spindle

- Press in the spindle locking button and turn the

spindle by hand until the spindle locking button

engages. (4) (3)

7.2 Placing the grinding wheel in position

See illustration A on page 2.

- Fit the support flange on the spindle. (2) The

flange should not turn on the spindle when

properly attached.

Only W 9-100: Screw support flange with two-hole

spanner onto spindle so that the small collar (with

diameter 16 mm) is facing upwards.

- Place the grinding disc on the support flange. (2)

The grinding disc must lay flat on the supporting

flange.

7.3 Securing/Releasing the "Quick"

clamping nut (depending on features)

Securing the (1)"Quick" clamping nut:

Only attach the "Quick" clamping nut (1) to

tools with "Metabo Quick System". These

tools can be identified by the red spindle lock button

(4) with "M-Quick" logo

Do not use the "Quick" clamping nut if the

accessory has a clamping shank thicker than

6.8 mm! In this case, use the 2-hole nut (13) with 2-

hole spanner (14).

- Lock the spindle (see chapter 7.1).

- Position the "Quick" clamping nut on the spindle

so that the 2 lugs engage in the 2 grooves on the

spindle. (1) (3) See illustration on page 2.

- Tighten the "Quick"clamping nut by turning

clockwise by hand.

-Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

5. Overview

6. Commissioning

7. Attaching the grinding disc

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEV 10-125 Quick Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info