Bedienungsanleitung Metabo WEVA 15-150 Quick (Seite 17 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

595536

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH en

occupational health and safety regulations,

disposal).

Collect the generated particles at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work (see

chapter 11.), thus less particles enter the

environment in an uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- Do not direct the escaping particles and the

exhaust air stream at yourself or nearby persons

or on dust deposits.

- Use an extraction unit and/or air purifiers

- Ensure good ventilation of the workplace and

keep clean using a vacuum cleaner Sweeping or

blowing stirs up dust

- Vacuum or wash the protective clothing Do not

blow, beat or brush

See page 2.

1 "Quick"clamping nut *

2Spindle

3 Autobalancer support flange *

4 Spindle locking button

5 Sliding on/off switch *

6Handle

7 Electronic signal indicator *

8 Thumbwheel for selection of speed *

9 Transport eyelet, for WEPBA 17-125 Quick,

WEPBA 17-150 Quick (Use only to transport

the machine)*

10 Paddle switch *

11 Additional handle/Additional handle with vibration

damping *

12 Safety cover

13 Support flange

14 2-hole nut *

15 2-hole spanner *

16 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle (11)

attached! Attach the additional handle on the

left or right of the machine and secure.

6.2 Attach the safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter11.Accessories!

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See illustration D on page 2.

- Push and hold the lever (16). Place the safety

guard (12) in the position indicated.

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is placed securely: The

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

(Disassemble in reverse order.)

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

- Press in the spindle locking button (4) and turn the

spindle (2) by hand until the spindle locking button

engages.

7.2 Placing the grinding wheel in position

WA..., WBA..., WE...A...:

See illustration A on page 2.

The Autobalancer support flange (3) is

permanently fitted on the spindle. As is the

case with most other angle grinders, a detachable

support flange is not necessary.

The contact surfaces of the Autobalancer

support flange (3), grinding wheel and the

"Quick" clamping nut (1) must be clean. Clean if

necessary.

- Place the grinding wheel on the Autobalancer

support flange (3).

The grinding wheel must lie flat on the

Autobalancer supporting flange.

WPB...:

See illustration B on page 2.

- Fit the support flange (13) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Place the grinding disc on the support flange (13).

The grinding disc must lay flat on the supporting

flange.

5. Overview

6. Commissioning

7. Attaching the grinding disc

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WEVA 15-150 Quick Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info