Bedienungsanleitung Metabo WX 2000 (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599584

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISHen

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands at the intended handles, take a secure

stance and concentrate on the work.

See illustration A on page 2.

Torque activation

Switching on:

Slide the lock (4) in the direction of

the arrow and press the trigger (5).

Switching off:

Release the trigger (5).

Continuous operation (depending on features)

Switching on:

Slide the lock (4) in the direction of the

arrow, press the trigger (5) and keep it

pressed. The machine is now switched on.

Now slide the lock (4) in the direction of the

arrow once more to lock the trigger (5)

(continuous operation).

Switching off:

Press the trigger (5) and release.

8.2 Working instructions

Grinding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Roughing: position the machine at an angle of 30° -

40° for the best working results.

Separating:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Sanding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Wire brushing:

Press down the machine evenly.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

Machine with "

X" in the model designation:

- Restart protection: The machine does not

start. The restart protection is active. If the mains

plug is inserted with the machine switched on, or if

the current supply is restored following an

interruption, the machine does not start up. Switch

the machine off and on again.

- When switched on, the machine accelerates

to maximum speed very quickly, i.e. automatic

restriction of the starting current does not work

(soft start). An electronic error exists. Other

safety-related electronic functions are no longer

available. Have the machine repaired immediately

(see 12.).

W 2000, W 2200-230:

- Switching on procedures produce brief reductions

in voltage. Unfavourable power conditions can be

detrimental to other devices. Power impedances

smaller than 0.2 ohm should not cause any

malfunction.

Use only genuine Metabo accessories.

Use only accessories that fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

See page 4.

A Roughing disc (always use with safety guard

attached)

B Louver disc (always use with safety guard

attached)

C Parting safety guard.

D Parting disc (always use with parting safety

guard attached)

E Diamond discs (always use with safety guard or

parting safety guard attached)

F Parting safety guard with guide slot (place on

machine and secure with screws.) (with adapter

for connection to a suitable dust extractor for

extraction of stone dust generated when cutting

stone slabs.)

G Hand guard (for attaching under the additional

side-mounted handle.)

H Extension piece (for working with supporting

discs. Increases the distance between the

spindle and the supporting disc by approx. 35

mm)

I Supporting disc for fibre discs (always attach

using the supporting disc clamping nut

supplied.) (always use with the hand guard

attached.)

J Fibre discs (always use with the hand guard

attached.)

8. Use

9. Cleaning

10. Troubleshooting

11. Accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WX 2000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info