Bedienungsanleitung Metabo WX 24-180 (Seite 17 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599595

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH en

decreases slightly. The machine is overloaded.

Work with a reduced load until the electronic

signal display goes out.

- Metabo S-automatic safety stop: The

electronic signal display (5) lights up and the

machine SWITCHES OFF automatically. If the

slew rate of the current is too high (for example, if

the machine suddenly seizes or kickback occurs),

the machine switches off. Switch off the machine

at the trigger (7). Switch it on again and continue

to work as normal. Try to prevent the machine

from seizing. See section 4.2.

- Restart protection: The electronic signal

display (5) FLASHES and the machine does

not start. The restart protection is active. If the

mains plug is inserted with the machine switched

on, or if the current supply is restored following an

interruption, the machine does not start up. Switch

the machine off and on again.

- When switched on, the machine accelerates

to maximum speed very quickly, i.e. automatic

restriction of the starting current does not work

(soft start). An electronic error exists. Other

safety-related electronic functions are no longer

available. Have the machine repaired immediately

(see 12.).

W 22-180, W 22-230, W 24-180, W 24-230,

W 26-180, W 26-230:

- Switching on procedures produce brief reductions

in voltage. Unfavourable power conditions can be

detrimental to other devices. Power impedances

smaller than 0.2 ohm should not cause any

malfunction.

Use only genuine Metabo accessories.

Use only accessories that fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

See page 4.

A Roughing disc (always use with safety guard

attached)

B Louver disc (always use with safety guard

attached)

C Parting safety guard.

D Parting disc (always use with parting safety

guard attached)

E Diamond discs (always use with safety guard or

parting safety guard attached)

F Cup wheel guard (place on machine and secure

with screws (f)). Secure cup wheel as described

in chapter 7.. Use an offset 2-hole spanner if

necessary. Use the wing screws to adjust the

safety guard until the cup wheel protrudes

between 0.5 cm - 1 cm.

G Cup wheels (always use with cup wheel safety

guard attached)

H Offset 2-hole spanner (for

securing/loosening

the clamping nut (12)

on cup wheels)

I Parting safety guard with guide slot (place on

machine and secure with screws.) (with adapter

for connection to a suitable dust extractor for

extraction of stone dust generated when cutting

stone slabs.)

J Hand guard (for attaching under the additional

side-mounted handle.)

K Extension piece (for working with supporting

discs. Increases the distance between the

spindle and the supporting disc by approx. 35

mm)

L Supporting disc for fibre discs (always attach

using the supporting disc clamping nut

supplied.) (always use with the hand guard

attached.)

M Fibre discs (always use with the hand guard

attached.)

Steel wire brushes

(always use with the hand

guard attached.)

O Bench cut-off stand

P Adjusting nut (12)

Q"Quick"clamping nut (1)

For complete range of accessories, see

www.metabo.com or refer to the main catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

The sanding dust generated may contain

hazardous materials: do not dispose of with the

household waste, but at a special collection point

for hazardous waste.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

Explanation of details on page 3 . Subject to

changes serving technical progress.

max

=max. diameter of accessory

max,1

=max. permitted thickness of clamping

shank on accessory when using clamping

nut (12)

max,2

=max. permitted thickness of clamping

shank on accessory when using

"Quick"clamping nut (1)

11. Accessories

12. Repairs

13. Environmental Protection

14. Technical Specifications

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WX 24-180 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info