Bedienungsanleitung Metabo WX 26-230 Quick (Seite 16 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

599590

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISHen

Do not use the "Quick" clamping nut

if the

accessory has a clamping shank thicker than

8mm

! In this case, use the clamping nut

(12) with 2-

hole spanner (13)

Only use the "Quick" clamping nut when

undamaged and in perfect operating condition

the arrow must point to the notch on the outer ring

(see illustration on page 2).

- Lock the spindle (see chapter 7.1).

- Fit the "Quick"clamping nut (1) on the spindle (3).

See illustration on page 2.

- Tighten the "Quick"clamping nut by turning

clockwise by hand.

- Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

Releasing the "Quick" clamping nut (1)

- Lock the spindle (see chapter 7.1).

- Turn the "Quick"clamping nut

(1)

anticlockwise to

unscrew.

7.4 Securing/Releasing the clamping nut

(depending on features)

Securing the clamping nut (12):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration D on page 2.

- A) For thin grinding wheels:

The edge of the clamping nut (12) faces upwards

so that the thin grinding wheel can be attached

securely.

B) For thick grinding wheels:

The edge of the clamping nut (12) faces

downwards so that the clamping nut can be

attached securely to the spindle.

- Lock the spindle. Turn the clamping nut (12)

clockwise using the 2-hole spanner (13) to

secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (12) anticlockwise using the 2-hole

spanner (13) to unscrew.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands at the intended handles, take a secure

stance and concentrate on the work.

See illustration A on page 2.

Torque activation

Switching on:

Slide the lock (6) in the direction of

the arrow and press the trigger (7).

Switching off:

Release the trigger (7).

Continuous operation (depending on features)

Switching on:

Slide the lock (6) in the direction of the

arrow, press the trigger (7) and keep it

pressed. The machine is now switched on.

Now slide the lock (6) in the direction of the

arrow once more to lock the trigger (7)

(continuous operation).

Switching off:

Press the trigger (7) and release.

8.2 Working instructions

Grinding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Roughing: position the machine at an angle of 30° -

40° for the best working results.

Separating:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Sanding:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

Wire brushing:

Press down the machine evenly.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

Button (8) for adjustment of the handle

(depending on features): Occasionally blow

compressed air through the button (when pressed,

in all 3 main handle positions).

Machine with "

X" in the model designation:

- Overload protection: The electronic signal

display (5) lights up and the load speed

decreases dramatically. The motor temperature

is too high! Run the machine in idling until it cools

down and the electronic signal display switches

off.

- Overload protection: The electronic signal

display (5) lights up and the load speed

8. Use

9. Cleaning

10. Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metabo WX 26-230 Quick Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info