776242
95
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
MI3002 MI3100 MI3102 IT supply systems
95
Step 5 Use the À key to select second live line (e.g. L2). Use the ½/¾ keys to
decrease indicative insulation resistance until insulation monitor device
alarms bad insulation. Indicative insulation resistance and calculated first fault
current between second live conductor (e.g. L2) and PE conductor are
displayed.
To complete measurement press the TEST key again.
After performing the measurement results with PASS/FAIL indication appear
on the display.
Figure B.8: First fault condition between L2 and PE
Displayed results:
R1...........Threshold indicative insulation resistance for L1,
I1 ............Calculated first fault leakage current at treshold insulation
resistance for L1,
R2...........Threshold indicative insulation resistance for L2,
I2 ............Calculated first fault leakage current at treshold indicative insulation
resistance for L2.
First fault leakage currents I1 and I2 are calculated as follows:
1
21
1R
U
ILL
=,
2
21
2R
U
ILL
=
where:
UL1-L2 .......Measured voltage between L1 and L2,
R1............Threshold insulation resistance for L1,
R2............Threshold insulation resistance for L2.
The calculated first fault current is the maximum current that would flow when
insulation resistance decreases to the same value as the applied test
resistance, and a first fault is assumed between opposite line and PE.
Save displayed results for documentation purposes. Refer to chapter 6.1.
Saving results.
Note:
It is recommended to disconnect all appliances from the tested supply net to
receive regular test results. Any connected appliance will influence the insulation
resistance threshold test.
The displayed resistances and currents are indicative only. Displayed resistance
can significantly differ from the actual resistance the Eurotest simulates. If IMD’s
with very low test currents (below 1mA) are checked the displayed resistance
value is typically lower (and current higher) than the actual simulated resistance.
The difference is lower for lower set resistances.
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metrel MI 3102 BT - Eurotest XE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Metrel MI 3102 BT - Eurotest XE

Metrel MI 3102 BT - Eurotest XE Bedienungsanleitung - Holländisch - 33 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info