Bedienungsanleitung Metz MECABLITZ 50 AF-1 digital Pentax (Seite 89 von 182) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

517341

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

If your flash unit is not going to be used for an extended period of time,

remove the batteries.

Replacing batteries

The batteries are flat or dead if the recycling time (elapsing from the triggering

of a full-power flash, e.g. in the M mode, to the moment the flash ready indica-

tor

ቤ

lights up again) exceeds 60 seconds.

• Turn off the flash unit at the main switch

ቢ

• Slide the battery compartment cover

ቪ

forwards

and fold open.

• Insert the batteries lengthwise as indicated by the

battery symbols provided. First, insert the batteries

that face the display and then the others.

Close the battery cover

ቪ

When inserting batteries, ensure that the polari-

ty is correct and matches the symbols in the bat-

tery compartment. Inserting the batteries in the

wrong direction can destroy the flash unit!

Always replace all batteries simultaneously, and

make sure that batteries are the same brand

and have the same capacity.

Flat or dead batteries should not be disposed

of with ordinary household waste. Help protect

the environment, and dispose of flat/dead bat-

teries at the appropriate collection points.

☞

3.3 Switching the flash unit on and off

The flash unit can be turned on by flipping the main

switch

ቢ

to the „ON“ position.

To turn off the flash unit, flip the main switch

ቢ

to the

left position.

If your flash unit is not going to be used for an

extended period of time, we recommend turning it off with the main

switch and removing the power source (i.e., batteries).

3.4 Auto OFF for the flash unit

To save battery power and prevent inadvertent battery drain, the flash unit is

factory-set to automatically switch to standby mode (Auto OFF) 10 minutes after

• being switched on,

• after pressing a key,

• a flash is fired

• the shutter release is actuated

• the camera’s exposure metering system is switched off.

...in stand-by mode, (Auto-OFF) is activated to save energy and to protect the

power source from unintentional discharging. The active automatic cut-off is

shown in the display . The flash ready indicator ቤ and the indicators on

the LC display disappear.

In slave mode, the automatic cut-off is not activated.

The most recently used operating setting is retained after automatic shutdown and

is immediately restored when the camera is switched on. The flash unit can be tur-

ned on again by pressing any button, or by tapping on the shutter release

(wake-up function).

The flash unit should always be turned off using the main switch

ቢ

if it

is not going to be used for an extended period.

If necessary, the Auto OFF function can be set to occur after 1 minute of inacti-

vity, or can be deactivated (see 9.4).

☞

709 47 0191.A3 50AF-1 Pen. 17.12.2010 13:22 Uhr Seite 89

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 50 AF-1 digital Pentax Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info