Bedienungsanleitung Metz MECABLITZ 60 CT-1 (Seite 31 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

517264

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

of f/4 has to be set on the camera. The adjusted aperture must be cor-

rected when the wide-angle diffuser is used.

5. Bounce Flash

Photos shot with full frontal flash are easily recognizable by their harsh, den-

se shadows. This is often associated with a sharp drop of light from the fore-

ground to the background.

This phenomenon can be avoided with bounce flash because the diffused

light will produce a soft and uniform rendition of both the subject and the

background. For this purpose the main reflector is turned in such a manner

that the flash is bounce back from a suitable reflective surface (e.g. ceiling or

walls of a room).

For this reason the main reflector can be turned vertically and horizontally.

The following are the vertical lock-in positions for bounce flash:

• 15°, 30°, 45°, 60°, 75° and 90° (simply tilt the reflector to the required

angle)

The head can be swivelled horizontally to the left and right by 180°, and

locks into position at 90° and 180°.

When swivelling the reflector vertically, it is essential to ensure that it is

turned by a sufficiently wide angle so that direct light can no longer

fall on the subject. Therefore, always tilt the reflector to at least the 60°

lock-in position.

The diffused light bounced back from the reflective surfaces results in a soft

illumination of the subject.

The reflecting surface must be white or a neutral colour, and it must not be

structured (e.g. wooden beams in the ceiling) as this could cast shadows. For

colour effects just select reflective surfaces in the required colour.

5.1 Bounced flash in automatic and TTL flash modes

It is advisable to check prior to the actual exposure whether the light is suffi-

cient for the selected aperture. Please refer to Ch. 2.5, for the corresponding

procedure.

☞

5.2 Bounce flash in manual flash mode

The required camera aperture in the manual flash mode is best established

with an exposure meter. Observe the following rule of thumb if an exposure

meter is not available

guide number

Camera aperture = —————————

light distance x 2

to establish the guide value for the aperture that can then be varied by +1

f–stop for the actual exposure.

6. Winder/Motordrive Mode

Definition:

In the winder/motordrive mode a series of pictures can be shot at the rate of

several frames per second. The winder mode is based on partial light output

levels.

Up to 2 flashes per second can be fired in the "Winder W" mode; up to 5

flashes per second are possible in the "Motordrive MD" mode.

Setting procedure for picture shooting in the winder flash mode:

• Set the camera as described in its Operating Instructions.

• Turn on the flash unit by its main switch ᕩ (fig. 5).

• Turn the setting knob ᕣ (fig. 4) for film speed on the reflector head. The

setting mark must be positioned at the given ISO film speed.

• Set the setting dial ³ (fig. 4) at “W” or “MD”

The distance will then be opposite an f-number. This f-number is the apertu-

re to be set.

• Await flash readiness indication – The flash ready indicator ቴ (fig. 3)

lights up.

The aperture to be set on the camera is then indicated on the scale opposi-

te the flash-to-subject distance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Metz MECABLITZ 60 CT-1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info