536841
10
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
c) After the inflation process remain in a quiet and relaxed sitting
position. The measurement now proceeds on its own. If no
measurement takes place and all that appears in the display is
aflashing,upwardspointingarrow,seebelowunder«Inflate
further». When the instrument detects a pulse, a heart symbol in
the display starts to flash.
d) A longer beep is sounded when the measurement has been
completed. The systolic, and diastolic blood pressures and pulse
rate now appear in the display.
At the same time, the cuff pressure will be automatically re-
leased by the quick release valve of the device.
5.5. Inflating further
If the cuff is not inflated sufficiently, the measurement is broken off
after a few seconds and a flashing arrow pointing upwards appears
in the display. It is then necessary to inflate further to at least
20 mmHg higher than the previous value. The instruction to inflate
further can appear several times if the pressure is still not sufficient.
Attention:
Ifthecuffisinflatedtoofar(over300mmHg),«HI»appearsinthe
display and a warning signal is sounded. The cuff pressure must
then be immediately released by pressing the 0/I button.
As soon as the cuff is inflated sufficiently and the measurement is
proceeding, continue as described under points c-d.
5.6. Discontinuing a measurement
If it is necessary to interrupt a blood pressure measurement for
any reason (e.g. the patient feels unwell), the O/I button can be
pressed at any time.
The device immediately lowers the cuff-pressure automatically.
5.7. Memory – displaying the last measurement
The measured results are stored in the instrument until
a new measurement is carried out or the batteries are
removed. You can call up the stored values at any time by
pressing the O/I button for at least 3 seconds.
6. Error messages/malfunctions
If an error occurs during a measurement, the measurement
is discontinued and a corresponding error code is displayed.
(Example Error no. 1)
7
MR
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Microlife BP 3AS1-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Microlife BP 3AS1-2

Microlife BP 3AS1-2 Bedienungsanleitung - Holländisch, Dänisch, Schwedisch, Norwegisch, Finnisch - 62 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info