Bedienungsanleitung Microlife BP A200 (Seite 6 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch, Norwegisch, Finnisch)

536793

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

3. Taking a Blood Pressure Measurement using this

Instrument

Checklist for taking a reliable measurement

1. Avoid activity, eating or smoking immediately before the

measurement.

2. Sit down for at least 5 minutes before the measurement and relax.

3. Always measure on the same arm (normally left).

4. Remove close-fitting garments from the upper arm. To avoid

constriction, shirt sleeves should not be rolled up - they do not

interfere with the cuff if they are laid flat.

5. Always ensure that the correct cuff size is used (marking on the

cuff).

 Fit the cuff closely, but not too tight.

 Make sure that the cuff is positioned 2 cm above the elbow.

 The artery mark located on the cuff (ca. 3 cm long bar) must

lie over the artery which runs down the inner side of the arm.

 Support your arm so it is relaxed.

 Ensure that the cuff is at the same height as your heart.

6. Press the ON/OFF button 1 to start the measurement.

7. The cuff will now pump up automatically. Relax, do not move

and do not tense your arm muscles until the measurement

result is displayed. Breathe normally and do not talk.

8. When the correct pressure is reached, the pumping stops and the

pressure falls gradually. If the required pressure was not reached,

the instrument will automatically pump some more air into the cuff.

9. During the measurement, the heart symbol BT flashes in the

display and a beep sounds every time a heartbeat is detected.

10.The result, comprising the systolic

and the diastolic

blood

pressure and the pulse

is displayed and longer beep is heard.

Note also the explanations on further displays in this booklet.

11.When the measurement has finished, remove the cuff.

12.Enter the result in the enclosed blood pressure pass and switch

off the instrument. (The monitor does switch off automatically

after approx. 1 min.).

How not to store a reading

Press the ON/OFF button 1 while the reading is being displayed.

Keep the button pressed until «M» AS is flashing and then release

it. Confirm by pressing the M-button again.



You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant

pressure sensation).



If the systolic blood pressure is known to be very high

it can be an advantage to set the pressure individually. Press

the ON/OFF button after the monitor has been pumped up to

a level of approx. 30 mmHg (shown on the display). Keep the

button pressed until the pressure is about 40 mmHg above

the expected systolic value – then release the button.

4. Appearance of the Heart Arrhythmia Indicator for

early Detection

This symbol AP indicates that certain pulse irregularities were

detected during the measurement. In this case, the result may

deviate from your normal blood pressure – repeat the measure-

ment. In most cases, this is no cause for concern. However, if the

symbol appears on a regular basis (e.g. several times a week with

measurements taken daily) we advise you to tell your doctor.

Please show your doctor the following explanation:

5. PC-Link Functions

This device can be used in connection with a personal computer

(PC) running the Microlife Blood Pressure Analyser (BPA) software.

The memory data can be transferred to the PC by connecting the

monitor via cable with the PC.

If no CD and cable is included download the BPA software from

www.microlife.com and use an USB cable with Mini-B 5 pin connector.

Installation and data transmission

1. Insert CD into CD ROM drive of your PC. The installation will

start automatically. If not, please click on «SETUP.EXE».

2. Connect the monitor via cable with the PC; no need to switch

the device on. 3 horizontal bars will appear on the display and

last for 3 seconds.

Information for the doctor on frequent appearance of the

Arrhythmia indicator

This instrument is an oscillometric blood pressure monitor that also

analyses pulse frequency during measurement. The instrument is

clinically tested.

The arrhythmia symbol is displayed after the measurement, if pulse

irregularities occur during measurement. If the symbol appears

more frequently (e.g. several times per week on measurements

performed daily) we recommend the patient to seek medical advice.

The instrument does not replace a cardiac examination, but serves

to detect pulse irregularities at an early stage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife BP A200 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info