Bedienungsanleitung Microlife BP A3 PC (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

536785

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 The individual results are not displayed. Your blood pressure

will only be displayed after all 3 measurements are taken.

 Do not remove the cuff between measurements.

 If one of the individual measurements was questionable, a

fourth one is automatically taken.

3. Taking a Blood Pressure Measurement using this

Device

Checklist for taking a reliable measurement

1. Avoid activity, eating or smoking immediately before the

measurement.

2. Sit down for at least 5 minutes before the measurement and relax.

3. Always measure on the same arm (normally left). It is recom-

mended that doctors perform double arm measurements on a

patients first visit in order to determine which arm to measure in

the future. The arm with the higher blood pressure should be

measured.

4. Remove close-fitting garments from the upper arm. To avoid

constriction, shirt sleeves should not be rolled up - they do not

interfere with the cuff if they are laid flat.

5. Always ensure that the correct cuff size is used (marking on the

cuff).

 Fit the cuff closely, but not too tight.

 Make sure that the cuff is positioned 2 cm above the elbow.

 The artery mark located on the cuff (ca. 3 cm long bar) must

lie over the artery which runs down the inner side of the arm.

 Support your arm so it is relaxed.

 Ensure that the cuff is at the same height as your heart.

6. Press the ON/OFF button 1 to start the measurement.

7. The cuff will now pump up automatically. Relax, do not move

and do not tense your arm muscles until the measurement

result is displayed. Breathe normally and do not talk.

8. When the correct pressure is reached, the pumping stops and the

pressure falls gradually. If the required pressure was not reached,

the device will automatically pump some more air into the cuff.

9. During the measurement, the pulse indicator BK flashes in the

display.

10.The result, comprising the systolic AP and the diastolic AQ

blood pressure and the pulse rate AR is displayed. Note also the

explanations on further display symbols in this booklet.

11.When the device has finished measuring, remove the cuff.

12.Switch off the device. (The monitor does switch off automati-

cally after approx. 1 min.).

How not to store a reading

Press the ON/OFF button 1 while the reading is being displayed.

Keep the button pressed until «M» BP is flashing and then release

it. Confirm by pressing the M-button again.



You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant

pressure sensation).



If the systolic blood pressure is known to be very high

it can be an advantage to set the pressure individually. Press

the ON/OFF button after the monitor has been pumped up to

a level of approx. 30 mmHg (shown on the display). Keep the

button pressed until the pressure is about 40 mmHg above

the expected systolic value – then release the button.

4. Appearance of the Pulse Arrhythmia Indicator for

early Detection

This symbol BN indicates that certain pulse irregularities were

detected during the measurement. In this case, the result may

deviate from your normal blood pressure – repeat the measure-

ment. In most cases, this is no cause for concern. However, if the

symbol appears on a regular basis (e.g. several times a week with

measurements taken daily) we advise you to tell your doctor.

Please show your doctor the following explanation:

5. Traffic Light Indicator in the Display

The bars on the left-hand edge of the traffic light display AS show

you the range within which the indicated blood pressure value lies.

Depending on the height of the bar, the readout value is either

within the optimum (green), elevated (yellow), too high (orange) or

dangerously high (red) range. The classification corresponds to

Information for the doctor on frequent appearance of the

Arrhythmia indicator

This device is an oscillometric blood pressure monitor that also

analyses pulse irregularity during measurement. The device is

clinically tested.

The arrhythmia symbol is displayed after the measurement, if

pulse irregularities occur during measurement. If the symbol

appears more frequently (e.g. several times per week on

measurements performed daily) we recommend the patient to

seek medical advice.

This device does not replace a cardiac examination, but serves

to detect pulse irregularities at an early stage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife BP A3 PC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info