Bedienungsanleitung Microlife FR 100 (Seite 6 von 102) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

536870

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

7. How to recall 12 readings in Memory Mode

This thermometer can recall the last 12 readings.

Pressing and releasing the START button 2 after the last

12 readings have been recalled will resume the above

sequence from reading 1.

8. Error Messages

9. Cleaning and Disinfecting

Use an alcohol swab or cotton tissue moistened with alcohol

(70% Isopropyl) to clean the thermometer casing and the

measuring probe. Ensure that no liquid enters the interior of

the thermometer. Never use abrasive cleaning agents, thin-

ners or benzene for cleaning and never immerse the instru-

ment in water or other cleaning liquids. Take care not to

scratch the surface of the probe lens and the display.

10.Battery Replacement

This instrument is supplied with one lithium battery, type

CR2032. Replace with a new CR2032 battery when the

flashing battery symbol appears on the display BT.

Remove the battery cover by sliding it in the direction

shown. Remove the battery and replace with a new one BK.

11.Guarantee

This instrument is covered by a 2 year guarantee from the

date of purchase. The guarantee is valid only on presenta-

tion of the guarantee card completed by the dealer (see

back) confirming date of purchase or the receipt.

Please contact Microlife-service.

• Recall mode AL: Press the START button 2 to enter

Recall mode when power is off. The memory icon «M»

will flash.

• Reading 1 - the last reading AM: Press and release the

START button 2 to recall the last reading. Display 1

alone with memory icon.

• Reading 12 - readings in succession: Press and

release the START button 2 consecutively to recall the

last 12 readings in succession.

• Measured temperature too high AN: Displays «H»

when measured temperature is higher than 42.2 °C or

108.0 °F.

• Measured temperature too low AO:

Displays «

» when

measured temperature is lower than 34.0 °C or 93.2 °F.

• Ambient temperature too high AP: Displays «H» in

conjunction with the «S» when ambient temperature is

higher than 40.0 °C or 104.0 °F.

• Ambient temperature too low AQ: Display «L» in

conjunction with the «T» when ambient temperature is

lower than 16.0 °C or 60.8 °F.

•

Error function display

The system has a malfunction.

• Blank display AS: Check if the battery has been loaded

correctly. Also check polarity (<+> and <->) of the battery.

• Flat battery indication BT: If the steady battery icon is

the only symbol shown on the display, the battery should

be replaced immediately.

Batteries and electronic instruments must be

disposed of in accordance with the locally appli-

cable regulations, not with domestic waste.

• The guarantee covers the instrument. Batteries and

packaging are not included.

•

Opening or altering the instrument invalidates the guarantee.

• The guarantee does not cover damage caused by

improper handling, discharged batteries, accidents or

non-compliance with the operating instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife FR 100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info