Bedienungsanleitung Microlife IR 120 (Seite 4 von 78) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

536871

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

 Never open this device.

 Earwax in the ear canal may cause a lower temperature

reading. Therefore it is important to ensure the subject's

ear canal is clean.

 This device comprises sensitive components and must

be treated with caution. Observe the storage and oper-

ating conditions described in the «Technical Specifica-

tions» section.

 Protect it from:

- extreme temperatures

- impact and dropping

- contamination and dust

- direct sunlight

- heat and cold

 If the device is not going to be used for a prolonged

period the battery should be removed.



Ensure that children do not use this device unsupervised;

some parts are small enough to be swallowed.

WARNING: Use of this device is not intended as

a substitute for consultation with your physician.

This device is NOT waterproof so do not immerse

in liquids.

3. How this Ear Thermometer measures

Temperature

This thermometer measures infrared energy radiated from

the eardrum and the surrounding tissue. This energy is

collected through the lens and converted to a temperature

value. The measured reading obtained directly from the

eardrum (Tympanic Membrane) ensures the most accurate

ear temperature.

Measurements taken from the surrounding tissue of the ear

canal generate lower readings and may result in misdiag-

nosis of fever.

To avoid an inaccurate measurement

1. Switch on the thermometer by pressing the ON/OFF

button 4.

2. After one beep is heard (and the temperature scale icon

is flashing), straighten the ear canal by gently pulling the

middle of the ear back and up.

3. Place the probe 1 firmly into the ear canal, press the

START button 2 and keep the probe in the ear until the

thermometer beeps to signal the completion of the

measurement.

4. Control Displays and Symbols

 All segments displayed 6: Press the ON/OFF button

4 to turn on the unit; all segments will be shown for

2 seconds.



Memory

The last reading will automatically be shown

on the display for 2 seconds.

 Ready for measurement 8: When the unit is ready for

measurement, the «°C» or «°F» icon will keep flashing.

 Measurement complete 9: The reading will be shown

on the display 3 with the «°C» or «°F» icon; the unit is

ready for the next measurement, when the «°C» or «°F»

icon is flashing again.

 Out-of-ear temperature indication AT: A crossed-ear-

icon will appear on the display 3 if the reading falls

outside the range 32.0  42.2 °C / 89.6  108.0 °F.

 Low battery indicator AK: When the unit is turned on,

the battery icon will keep flashing to remind the user to

replace the battery.

5. Directions for Use

1. Press the ON/OFF button

. The display

is activated

to show all segments for 2 seconds.

2. The last measurement reading will automatically be

shown on the display for 2 seconds with the «

» icon

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife IR 120 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info