Bedienungsanleitung Microlife IR 150 (Seite 5 von 55) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

536861

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

3IR 150

Measurements taken from the surrounding tissue of the ear canal

generate lower readings and may result in misdiagnosis of fever.

To avoid an inaccurate measurement

1. Switch on the thermometer by pressing the ON/OFF button 4.

2. After one beep is heard (and the temperature scale icon is

flashing), straighten the ear canal by gently pulling the middle

of the ear back and up.

3. Place the probe 1 firmly into the ear canal, press the START

button 3 and keep the probe in the ear until the thermometer

beeps to signal the completion of the measurement.

4. Control Displays and Symbols

 All segments displayed 7: Press the ON/OFF button 4 to

turn on the unit; all segments will be shown for 1 second.

 Ready for measurement 9: When the unit is ready for

measurement, the «°C» or «°F» icon will keep flashing.

The probe LED light is activated for 10 seconds.



Measurement complete

The reading will be shown on the

display

with the «

°C

» or «

°F

» icon; the unit is ready for the

next measurement, when the «

°C

» or «

°F

» icon is flashing again.

 Out-of-ear temperature indication AK: A crossed-ear-icon will

appear on the display 2 if the reading falls outside the range

32.0  42.2 °C / 89.6  108.0 °F.

 Low battery indicator AL: When the unit is turned on, the «»

icon will keep flashing to remind the user to replace the battery.

5. Setting Date, Time and Beeper Functions

Setting the date and time

1. After the new battery is fitted, the year number flashes in the

display

. You can set the year by pressing the START button

To confirm and then set the month, press the M-button

2. Press the START button 3 to set the month. Press the M-

button 6 to confirm and then set the day.

3. Follow the previously mentioned instructions to set the day, 12

or 24 hour mode, hours and minutes.

4. Once you have set the minutes and pressed the M-button 6,

the date and time are set and the time is displayed.



If no button is pressed for 20 seconds, the device automat-

ically switches to ready for measuring 9.



Cancel time setup: Press the ON/OFF button 4 during

time setup. The LCD will show Date/Time icons with «--:--».

After that press the ON/OFF button 4 to start the measure-

ment. If no further action is taken within 60 seconds, the

device will automatically turn off.



Change current date and time: Press and hold the M-

button 6 for approx. 3 seconds until the year number

starts to flash BN. Now you can enter the new values as

described above.

Setting the beeper

1. When the device is switched off, press and hold the ON/OFF

button 4 for 5 seconds to set the beeper BO.

2. Press the ON/OFF button 4 again to either turn the beeper on

or off. The beeper is activated when the beeper icon BO is not

crossed-out.



If no button is pressed for 5 seconds, the device automati-

cally switches to ready for measuring 9.

6. Directions for Use

1. Press the ON/OFF button 4. The display 2 is activated to

show all segments for 1 second.

2. When the «°C» or «°F» icon is flashing, a beep sound is heard

and the thermometer is ready for measuring 9.

3. The probe LED light is activated and will automatically turn off

after 10 seconds.

4. Straighten the ear canal by pulling the ear up and back to give

a clear view of the eardrum.

 For children under 1 year; pull the ear straight back.

 For children of 1 year to adult; pull the ear up and back.

Also refer to the short instructions at the front.

5. While gently pulling the ear, insert the probe snugly into the ear

canal

(about 1 sec.)

and

immediately

press the START button

. Release the button and wait for the beep sound. This indicates

the end of the measurement.

6. Remove the thermometer from the ear canal. The display shows

the measured temperature



NOTE:

 To ensure accurate readings, wait at least 30 sec. after 3-5

continuous measurements.

 Accumulation of ear wax on the probe can result in less accu-

rate temperature readings or cross infection between users.



It is essential that the probe is cleaned after every measure-

ment.

Therefore, this device reminds the user to clean the probe

when turning off the device. «CLEAN ME»

is displayed and

the probe LED light will flash for 3 seconds. For cleaning, follow

the instructions in the «Cleaning and Disinfecting» section.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife IR 150 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info