Bedienungsanleitung Microlife IR 210 (Seite 4 von 81) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

773464

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite



Do not use this device close to strong electromagnetic fields such

as mobile telephones or radio installations. Keep a minimum

distance of 3.3 m from such devices when using this device.

Protect it from:

- extreme temperatures

- impact and dropping

- contamination and dust

- direct sunlight

- heat and cold

If the device is not going to be used for a prolonged period the

battery should be removed.

WARNING: The measurement results given by this device

is not a diagnosis. It is not replacing the need for the consul-

tation of a physician, especially if not matching the patient’s

symptoms. Do not rely on the measurement result only,

always consider other potentially occurring symptoms and

the patient’s feedback. Calling a doctor or an ambulance is

advised if needed.

3. How this Thermometer measures Temperature

This thermometer measures infrared energy radiated from the

eardrum and the surrounding tissue. This energy is collected

through the lens and converted to a temperature value. The

measured reading obtained directly from the eardrum (Tympanic

Membrane) ensures the most accurate ear temperature.

Measurements taken from the surrounding tissue of the ear canal

generate lower readings and may result in misdiagnosis of fever.

To avoid an inaccurate measurement

1. Fit a new Microlife branded and undamaged probe cover CK on

the measuring sensor 1.

2. Switch on the thermometer by pressing the START/IO button

3. After one beep is heard (and the temperature scale icon is

flashing), straighten the ear canal by gently pulling the middle

of the ear back and up.

4. Place the probe 1 firmly into the ear canal. «Good» will be

displayed with a short beep to confirm the device has detected

the correct position. Press the START/IO button 6 and keep

the probe in the ear until the thermometer beeps to signal the

completion of the measurement.

4. Control Displays and Symbols

All segments displayed 7: Press the START/IO button 6 to

turn on the unit; all segments will be shown for 1 second.

Ready for measurement 9: When the unit is ready for

measurement, the «°C» or «°F» icon will keep flashing.

The probe LED light is activated and will keep flashing.



Correct position indication

The probe LED light will stop

flashing (stays illuminated) and «good» will be displayed on the

LCD, when the measuring sensor detects an appropriate position.



Measurement complete

The reading will be shown on the

display

with the «

°C

» or «

°F

» icon; the unit is ready for the

next measurement, when the «

°C

» or «

°F

» icon is flashing again.

Low battery indicator AP: When the unit is turned on, the

«battery» icon will keep flashing to remind the user to replace

the battery.

5. Setting Date, Time and Beeper Functions

Setting the date and time

1. After the new battery is fitted, the year number flashes in the

display BQ. You can set the year by pressing the M-button 3.

To confirm and then set the month, press the MODE button 4.

2. Press the M-button 3 to set the month. Press the MODE

button 4 to confirm and then set the day.

3. Follow the previously mentioned instructions to set the day,

hours and minutes.

4. Once you have set the minutes and pressed the START/IO

button 6, the date and time are set and the time is displayed.

If no button is pressed for 20 seconds, the device automat-

ically switches to ready for measuring 9.



Cancel time setup:

Press the START/IO button

during

time setup. The LCD will show Date/Time icons with «--:--».

After that press the START/IO button

to start the measure-

ment. If no further action is taken within 60 seconds, the

device will automatically turn off.



Change current date and time:

Press and hold the MODE

button

for approx. 8 seconds until the year number starts

to flash

. Now you can enter the new values as described

above.

Setting the beeper

1. Press and hold the MODE button 4 for 3 seconds to set the

beeper BR.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife IR 210 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info