Bedienungsanleitung Microlife NC 120 (Seite 6 von 81) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch, Norwegisch, Finnisch)

536867

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

8. How to recall 30 readings in Memory Mode

This thermometer can recall the last 30 readings.

 Recall mode AP: Press the START button 3 to enter

Recall mode when power is off. The memory icon «M»

will flash.

 Reading 1 - the last reading AQ: Press and release the

START button 3 to recall the last reading. Display 1

alone with memory icon.

 Reading 30 - readings in succession: Press and

release the START button 3 consecutively to recall the

last 30 readings in succession.

Pressing and releasing the START button 3 after the last

30 readings have been recalled will resume the above

sequence from reading 1.

9. Error Messages



Measured temperature too high

Displays «

when measured temperature is higher than 42.2 °C /

108.0 °F in body mode or 100 °C / 212 °F in object mode.

 Measured temperature too low AS: Displays «L»

when measured temperature is lower than 34.0 °C /

93.2 °F in body mode or 0 °C / 32 °F in object mode.

 Ambient temperature too high BT: Displays «H» in

conjunction with the when ambient temperature is

higher than 40.0 °C / 104.0 °F.

 Ambient temperature too low BK: Display «L» in

conjunction with the when ambient temperature is

lower than 16.0 °C / 60.8 °F in body mode or lower than

5.0 °C / 41.0 °F in object mode.



Error function display

The system has a malfunction.



Blank display

Check if the battery has been loaded

correctly. Also check polarity (<+> and <->) of the battery.

 Flat battery indication BN: If the steady battery icon is

the only symbol shown on the display, the battery should

be replaced immediately.

10.Cleaning and Disinfecting

Use an alcohol swab or cotton tissue moistened with alcohol

(70% Isopropyl) to clean the thermometer casing and the

measuring probe. Ensure that no liquid enters the interior of

the thermometer. Never use abrasive cleaning agents, thin-

ners or benzene for cleaning and never immerse the instru-

ment in water or other cleaning liquids. Take care not to

scratch the surface of the probe lens and the display.

11.Battery Replacement

This instrument is supplied with one lithium battery, type

CR2032. Replace with a new CR2032 battery when the

flashing battery symbol appears on the display BN.

Remove the battery cover by sliding it in the direction

shown. Remove the battery and replace with a new one BO.

Batteries and electronic instruments must be dis-

posed of in accordance with the locally applicable

regulations, not with domestic waste.

12.Guarantee

This instrument is covered by a 2 year guarantee from the

date of purchase. The guarantee is valid only on presenta-

tion of the guarantee card completed by the dealer (see

back) confirming date of purchase or the receipt.

 The guarantee covers the instrument. Batteries and

packaging are not included.

 Opening or altering the instrument invalidates the guar-

antee.

 The guarantee does not cover damage caused by

improper handling, discharged batteries, accidents or

non-compliance with the operating instructions.

Please contact Microlife-service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife NC 120 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info