Bedienungsanleitung Microlife OXY 210 (Seite 6 von 75) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

773555

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

The device must be able to measure the pulse

properly to obtain an accurate SpO2 measure-

ment. Verify that nothing is hindering the pulse

measurement before relying on the SpO2

measurement.

The maximum application time at a single site

should be less than 30 minutes, in order to

ensure correct sensor alignment and skin integ-

rity.

Inaccurate measurements may occur if:

The patient suffers from significant levels of dysfunc-

tional hemoglobin (such as carboxyhemoglobin or

methemoglobin).

Intravascular dyes such as indocyanine green or meth-

ylene blue have been injected into the patient.

Used in the presence of high ambient light (e.g. direct

sunlight). Shield the sensor area with a surgical towel if

necessary.

There is excessive patient movement.

The patient experiences venous pulsations.

The patient has hypotension, severe vasoconstriction,

severe anemia, or hypothermia.

The patient is in cardiac arrest or is in shock.

Fingernail polish or false fingernails are applied.

6. Inserting the batteries

After you have unpacked your device, first insert the

batteries. The battery compartment is on the bottom of the

device. Remove the battery cover by sliding it in the direc-

tion shown. Insert the batteries (2 x 1.5 V, size AAA),

thereby observing the indicated polarity.

Replace the batteries when the low power indi-

cator 5 appears on the display.

Always replace both batteries at the same time.

7. ON/OFF button

/ Function button

Press and release the ON/OFF button 1 to turn on, hold

the button for about one second. The device shows the

settings menu AT. Press or hold the ON/OFF button to

perform corresponding operations. Hold it to set an item, or

press it to switch an option or switch the display mode.

Press means no more than 0.5 seconds, while hold means

more than 0.5 seconds.

Alert Sound Setting

Hold ON/OFF button 1 while the device is switched

on.Settings menu (interface 1) is displayed AT-a. Move «*»

to the corresponding option, and hold the function button to

set Alm to on and set Beep to off. When Alm is set to on

and the measured values of the blood oxygen saturation

and pulse rate go beyond the upper limit or lower limit, the

device gives off an alert sound. When Beep is set to on, a

tick will be heard along with pulse beats during pulse rate

measurement. While the «*» symbol stays on the Restore

option, hold the functional button to restore default settings.

Brightness Setting

Press ON/OFF button 1 to select the Brightness option

and then hold the ON/OFF button to set the brightness to a

value ranging from 1 to 5. The greater the value, the

greater the brightness of the screen.

Alert Range Setting

On settings menu (interface 2) AT-b, press the ON/OFF

button 1 to switch between options. On this interface, you

can set the upper limit and lower limit of SpO2 Alm and PR

Alm. While the «*» symbol stays on the +/- option, hold the

functional button to set the option to + or -.

In + mode, select the corresponding option and hold the

ON/OFF button to increase the upper or lower limit; in -

mode, hold the ON/OFF button to decrease the upper or

lower limit. Move «*» to the Exit option, and hold the ON/

OFF button to return to the monitoring interface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Microlife OXY 210 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info