Bedienungsanleitung Midas DL351 PRO6 (Seite 11 von 70) (Englisch)

658493

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

DL351 Modular I/O

Operator Manual

Precautions

Before installing, setting up or operating this equipment make sure you have read and

fully understand all of this section and the “IMPORTANT SAFETY INSTRUCTIONS” at the

front of this manual.

This equipment is supplied by a mains voltage that can cause electric shock injury!

The following must be observed in order to maintain safety and electromagnetic compatibility (EMC)

performance.

Safety warnings

Signal 0V is connected internally to the

chassis.

To electrically isolate this equipment, while

observing full safety precautions (see

“Power” below), switch off the two isolator

switches (above the mains sockets on the

rear panel of the unit) one at a time and

then switch off the mains at the two mains

outlets. Isolate the unit by unplugging the

two mains leads from rear panel.

To avoid electrical shock do not remove

covers.

General precautions

In the event of ground loop problems,

disconnect the signal screen at one end of the

connecting cables. Note that this can only be

done when the equipment is used within a

balanced system.

Do not remove, hide or deface any warnings or

cautions.

Power

The power supplies contain LETHAL VOLTAGES

greatly in excess of the mains voltage and its

rails can produce extremely large currents that

could burn out equipment and wiring if shorted.

The internal power supplies are of the switch

mode type that automatically sense the

incoming mains voltage and will work where the

nominal voltage is in the range 100VAC to

240VAC.

Each mains inlet is to be sourced from its own

separate wall-mounted mains outlet socket.

Otherwise, their mains sources must be suitably

distributed so as to meet local safety

regulations.

A Volex locking type plug is fitted on each

supplied mains cable, which plugs into a mains

IEC connector on the unit. When fitted properly

the Volex plug locks into place, preventing it

from working loose, or being inadvertently

knocked loose or pulled out. To fit a Volex plug,

insert it into the mains IEC connector and push

it in until it locks in place. Then, check to make

sure it is locked in place. To remove it, release

its locking device and then pull it out. When

fitting or removing a Volex plug, always hold the

plug itself and never use the cable, as this may

damage it.

When removing the equipment’s electric plugs

from the outlets, always hold the plug itself and

not the cable. Pulling out the plug by the cable

can damage it.

Never insert or remove an electric plug with wet

hands.

Do not connect/disconnect a mains power

connector to/from the unit while power is being

applied to it. Switch the power off first.

Switch the mains isolator switches on/off one at

a time. Do not switch them both on/off

simultaneously.

Handling the equipment

Completely isolate the equipment electrically

and disconnect all cables from the equipment

before moving it.

When lifting or moving the equipment, always

take its size and weight into consideration. If

necessary, use suitable lifting equipment or

transporting gear, or sufficient additional

personnel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas DL351 PRO6 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info