Bedienungsanleitung Midas M32 (Seite 48 von 61) (Englisch)

658461

Zoom out

Zoom in

Vorherige Seite

1/61

Nächste Seite

48 M32 DIGITAL CONSOLE User Manual

4.2 Appendix B: MIDI Operation

MIDI RX > Scenes

Whenever Program Change messages in the range 1-100 are received on MIDI

CH01, thecorresponding scene of the M32 internal show memory will be loaded.

This requires the following preconditions:

SETUP / remote

• MIDI In/Out check marks must be set according to the connection on which

MIDI input will be accepted (via physical MIDI connectors on M32 or S16, or

via DN32-USB card)

• MIDI In/Out check mark must be set for “Enable MIDI Scene Recall”.

SETUP / global

• When tick mark “Conrm Pop-Ups” / “Scene Load” is active, MIDI scene

recalls will only become active after manual conrmation

• If you prefer activating scenes via MIDI Program Changes immediately,

un-check the “ConrmPop-Ups” / “Scene Load” tick mark.

SHOW CONTROL VIEW / home

• Valid scenes must be stored in the internal M32 show le. It is not possible to

recall emptyscenes

• The scope of changes applied by a MIDI scene recall depends on the Scene

Safes, ParameterSafes and Channel Safes settings, same as with recalling

the scene locally.

MIDI TX > Scenes

Every scene can be assigned one specic MIDI command/event. Each time the

scene is loaded the MIDI command will be sent out once. Possible choices for MIDI

commands/events to be found on Scenes View/MIDI page:

• O > no message will be sent upon scene load

• Program Change > select the MIDI Channel and the Program Number (using

knobs 4/5 at the main display)

• Control Change > select the MIDI Channel, Controller number and

value(using knobs 4-6 at the main display)

• Note > select the MIDI Channel, Note number and velocity(using knobs 4-6

at the maindisplay).

Will send out a Note On command directly followed by the same

NoteOcommand.

Permanent MIDI Assignments Overview (Remote O)

MIDI RX MIDI Ch Controller Value Comment

Scenes 1 Program Change 1-100

Snippet 2 Program Change 1-100

Cue 3-6 Program Change 0-127 Ch3 -> Cue 1-127, Ch4 -> Cue 128-255, etc.

Mute Groups 2 CC80-85 on (127) / o (0), toggle latching

Faders 1 CC0-79 0-127 Value 95 = 0dB

Mute 2 CC0-79 on (127) / o (0), toggle latching

Pan 2 CC0-79 0-127 Value 64 = Pan Mid

MIDI TX MIDI Ch Controller Value Comment

Mute Groups 2 CC80-85 on (127) / o (0), toggle latching

Faders 1 CC80-79 0-127 Value 95 = 0dB

Mute 2 CC80-79 on (127) / o (0), toggle latching

Pan 3 CC80-79 0-127 Value 64 = Pan Mid

MIDI RX > Assign

Whenever assignable controls are set up for transmitting MIDI commands,

reception of that same command (status or continuous) will be reected on the

respective assignable control element (buttonlight, encoder LED collar).

MIDITX > Assign

The assignable MIDI commands have been restricted to some generic elements:

Encoders 1-4 > can be assigned to sending control changes, program changes

ornotes.

• Parameters are currently ‘Channel’ and ‘Value’

• For CC and Note commands ‘Value’ = controller number/note number, and

the encoder rotation determines the controller value/note-on velocity

• For Program Changes only the channel is specied, and the encoder rotation

determines the programnumber

Buttons 5-12 > can be operated in two modes, ‘MIDI Push’ (non-latching)

formomentary commands, or ‘MIDI Toggle’ (latching) for static commands.

MIDI Push

Can be assigned to sending control changes, program changes or notes

Parameters are currently ‘Channel’ and ‘Value’

For CC and Note commands ‘Value’ 0…127 = controller number/note number,

and the button momentarily toggles the controller value/note-on velocity

To 127 (depressed/released]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midas M32 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info