Bedienungsanleitung Midea 36QMS5GP482EEP001 (Seite 10 von 16) (Englisch)

684500

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Control knob for minute minder

(for same models)

The minute minder is a countdown

timer which emits an audible signal

when the cooking time has elapsed.

The minute minder runs

independently of the oven.

Use this control knob to set the

cooking time.

USE OF THE ELECTRIC GRILL

Accessories

The accessories can be inserted in the oven in 4 different shelf

positions.

You can pull the accessories two-thirds of the way out without

them tipping. This allows meals to be removed easily.

You can buy accessories from the after-sales service or from

specialist retailers.

Baking and roasting shelf

For ovenware, cake tins,

roasts, grilling and frozen

meals.

Enamelled baking tray

For moist cakes, pastries,

frozen meals and large

roasts. Can also be

inserted underneath the

wire rack or rotary spit and

used as a drip tray to

collect fat.

Rotary spit

For roasts and large pieces

of poultry. Use only in

combination with the

enamelled baking tray.

Accessory Description

Setting Meaning

Off

1 - 59 Cooking time in minutes

Bump

Install shelves by locating them in the horizontal guide rails on

the oven walls. The raised portion of the shelf is to be facing

the rear wall of the oven.

USING THE GRILL

Turn the oven knob to the right and place it on the grill

position. The grill pan should be located on the top oven shelf

position. Always preheat the grill on full for 3-5 minutes before

inserting the food.

The user can change the shelves, depending on his personal

whishes and on the different food.

To remove the shelves from the oven, pull them forward

you, tilt front end upward and pull them out.

To replace it in the opposite manner as before.

As shown in the picture, on-off control is used to control

heating components of oven, the left is power source which

can be connected under the 220V.

1Time Adjustment after Starting up

When the power is on, it shows 12:00 and flashes. The relay

contact is disconnected, auto-programming icon keeps

lighting up, time setting icon flashes.

Press K1 or K3 to the time or press K2 to get into the present

working mode. The relay contact is connected.

Press K2 by 4 times to get into the present time-setting mode

under the common mode.

2Alarm and Buzz Function

Press K2 once under the common mode: "Alarm Icon"

flashes.”

Press K1 or K3 to adjust the present alarm clock.

5s after adjusting to the time you need, "Alarm Icon" keeps

flashing, and will work after setting up. In this case, pressing

K1 can know the alarming time( it will show seconds at one

ast minute).

When alarm counts down to zero, alarming program ends,

alarm icon flashes, and the buzzer os buzzing. Press any key

to stop the buzzing or it will turn off automatically after 2

minutes.

3 Auto-programming Setting and Instructions

 Semiautomatic program mode

Use this setting for oven working time, automatic heating

switch-off at the end of setting time, buzzer will inform the

user.

Press K2 twice or three times to get into the auto-program-

ming time setting, “Auto-programming Icon” flashes. Press

K1 and K3 to aujust continuous time and end time.

5s after setting, it will work automatically, "Auto-program-

ming Icon" keeps lighting up. If continuous time is 0, turn

off the relay contact, and "Relay Operation Icon" is dark,

"Autoprogramming Icon" flashes, the buzzer is buzzing.

This mode’s range of continuous time and end time:

Adjustment range for continuous time: >0 but <10 hours

Adjustment range for end time: present time< end time < =

present time + 10 hours.

If meet this standard: end time = present time + continuous

time.

For example: the present time is 2: 00, then the max. end time

is adjusted to 12:00 (2: 0010001200). When the end time is

adjusted to 12:00, then the continuous time is 10:00.

5s after adjusted, automatic program is working.

After 10 hours, if continuous time is counting down to 0, turn

off the relay contact, and “Relay Operation Icon” is dark,

“Auto-programming Icon” flashes, the buzzer is buzzing.

Note:

1. only use this setting for either continuous time or end time.

For example: the present time is 2:00, and if let the oven

work for 3 hours, set the continuous time to 3:00, and the

end time will automatically change to 5:00 and vice versa.

2. If the continuous time is equal to 0 or the end time is equal

to the present time, it means that the automatic program is

over.

3. When the automatic program is over, the continuous time is

0 and the end time is equal to the present time.

Automatic Mode

Use this mode for setting oven’s starting time and end time,

which means make an appointment to boot. When the time is

over, it will automatically turn off the heating and the buzzer is

buzzing to inform the user.

Press twice to get into the continuous time setting mode

under the common mode, press three times to get into the

end time.

When the continuous time setting is ok or the end time setting

is ok, then press K2 to get into the other kind of automatic

program time setting, "Auto-programming Icon" flashes,

press K1 and K3 to ad just continuous time and end time

setting mode.

5s after automatic program setting, it will automatically work,

and "Auto-programming Icon" keeps lighting up. Turn off the

relay conntact, and the icon i s dark. When work until the

starting time, the relay contact is connected, the icon is light.

When the continuous time is counting down, if the continuous

time is 0,turn off the relay contact, "Relay Operation Icon" is

dark, "Auto-programming Icon" flashes, and the buzzer is

buzzing.

The continuous time and the end time under this model will be

set as follow: Starting time = end time - continuous time

For example, the present time is 2:00, set the continuous time

to 3:00, and the end time to 10:00, then the starting time is

7:00 (7:0010:003:00). The relay contact is connected and its

icon is light. After working for continuous 3 hours, the

continuous time is 0, turn off the relay contact, "Relay

Operation Icon" is dark, “Auto-programming Icon” flashes,

the buzzer is buzzing.

Note:

1 End time > present time + continuous time,

< but 23 hours and 59 minutes

For example: the present time is 2:00, continuous time is

0:01, then the range for end time is 2:02 (2:02 2:00+1).

2 Continuous time> 1 minute, continuous time and end time

both will be set.

3 If the continuous time is equ al to 0 or the end time is equal

to the present time it meas the automatic program is over.

4 When the automatic program is over, the continuous time is

0, and the end time is the same with the present time.

4Cancel Function

When semiautomatic or automatic function is starting, press

K1 and K3 at the same time which can cancel the automatic

mode. (to cancel continuous time and end time).

Midea 36QMS5GP482EEP001 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info