Bedienungsanleitung Midea MCB12HRN2 (Seite 9 von 10) (Englisch)

588176

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Connect Panel with Swing Motor Wire Connector (white) and Remote Controller Wire Connector

after passing through a hole. (Chart 18)

Hole

Swing Motor Wire

Chart 18 Swing Motor Wire

Swing Motor Wire

Installation Screws

Nut Cap

Chart 19 Installation sequence of screws

Confirm the wires are not nipped between the panel and the Indoor Unit, or the panel and the

ceiling. Then fasten the screws according to the following. (chart 19)

1) Fix the panel at central point temporarily.

2) Confirm and adjust the position.

3) Fix left side of panel (from to ) temporarily.

4) Fix right side of panel (from to ) temporarily.

5) Confirm the installation position.

6) Fasten the , , , , screws tightly.

After tightening Panel Screws, install two screw caps to the screws at side of Air Outlet. (chart 19 )

Lead Swing Motor Wire into a hole. (Chart 18)

Hang the Strip Hook of Inlet Grille to the hole in the middle of

Indoor Unit Air Inlet. (Chart 20)

Hole

Strip Hook

Chart 20 Hang the Strip Hook of Inlet Grille

NOTICES FOR BENDABLE PIPE

The bending angle should not exceed 90 .

Bending position is preferably in the bendable pipe. The larger the better it is.

Do not bend the pipe more than three times.

BEND THE CONNECTING PIPE OF SMALL WALL THICKNESS

Cut out a desired concave at the bending part of the insulating pipe. Then expose the pipe (cover

it with tapes after bending).

To prevent collapsing or deforming, please bend the pipe at its biggest radius.

Use bender to get a small radius pipes.

USE THE MARKET BRASS PIPE

Be sure to use the same insulating materials when you buy the brass pipe.

2. Locate The Pipe

Drill a hole in the wall (suitable just for the size of the wall conduit, 90mm in general), then set on the

fittings such as the wall conduit and its cover.

Bind the connecting pipe and the cables together tightly with binding tapes. Do not let air in, which

will cause water leakage by condensation.

Pass the bound connecting pipe through the wall conduit from outside. Be careful of the pipe

allocation to do no damage to the tubing.

Connect the pipes.

Then, open the stem of stop values of the outdoor unit to make the refrigerant pipe connecting the

indoor unit with the outdoor unit in fluent flow.

Be sure of no leakage by checking it with leak detector or soap water.

Cover the joint of the connecting pipe to the indoor unit with the soundproof / insulating sheath

(fittings), and bind it well with the tapes to prevent leakage.

FLARING

90 +4

lean crude burr

Chart 28

Chart 29

Outside-

diameter

A (mm)

max

min

F6.35mm

F9.53mm

F12.7mm

8.7

12.4

15.8

8.3

15.4

1. Cut a pipe with a pipe cutter.

2. Insert a flare nut into a pipe and flare the pipe.

Table 1

EXPEL THE AIR

REFRIGERANT PIPE CONNECTING

FASTEN THE NUT

Put the connecting tubing at the proper position,

wrench the nuts with hands then fasten it with a

wrench. (Refer to Chart 30)

Chart 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MCB12HRN2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MCB12HRN2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info