Bedienungsanleitung Midea MFA-18HRDN1 (Seite 10 von 24) (Englisch)

588604

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

installation manual

Bend the tubing in proper way. Do not harm to them.

Connect the indoor unit at first, then the outdoor

unit.

Too large torque will harm the bellmouthing and too small

will cause leakage. Please determine the torque

according to Table 4.

After the connecting work is finished, be sure to check

that there is no gas leak.

The bending angle should not exceed 90.

Bending position is preferably in the middle of the

bendable pipe. The larger the bending radius the better it

is.

Do not bend the pipe more than three times.

When connecting the flare nut, coat the flare both inside

and outside with either oil or ester oil and initially tighten

by hand 3 or 4 turns before tighting firmly.

Bend the pipe with thumb

min-radius 100mm

CAUTION

How to expel the air with a vacuum pump

Stop valve operation introduction

1. Opening stop valve

Remove the cap and turn the valve

counterclock-wise with the hexagon wrench.

Turn it until the shaft stops.Do not apply excessive force

to the stop valve. Doing so may breakthe valve body, as

the valve is not a backseat type. Always use the special

tool.

Make sure to tighten the cap securely.

Fig.7-6

Fig.7-7

Fig.7-8

Be sure to use both a spanner and torque wrench

together when connecting or disconnecting pipes to /from

the unit.

CAUTION

Always use a charge hose for service port connection.

After tightening the cap, check that no refrigerant leaks

arepresent.

Make sure to tighten the cap securely.

For the tightening torque,refer to the table below.

Table 7-3

Tightening torque N M (Turn clockwise to close)

Stop

Valve size Shaft (valve body)

Cap

(Valve lid)

Ø6.35

Hexagonal

wrench 4 mm

Ø9.53

Ø12.7

Ø16

Hexagonal

wrench 6 mm

Ø22.2 Hexagonal

wrench

10 mm

Ø25.4

Maintenance

nut

36 44

23 27

18 22

13.5 16.55.4 6.6

8.1 9.9

13.5 16.5

27 33

11.5 13.9

Loosen and remove the maintenance nuts of stop valves A

and B, and connect the charge hose of the manifold valve to

the service port of stop valve A. (Be sure that stop valves A

and B are both closed)

Connect the joint of the charge hose with the vacuum pump.

Open the Lo-lever of the manifold value completely.

Turn on the vacuum pump. At the beginning of pumping,

loosen the maintenance nut of stop valve B a little to check

whether the air comes in (the sound of the pump changes,

and the indicator of compound meter turns below zero). Then

fasten the maintenace nut.

Using the vacuum pump

When the pumping has finished, close the Lo-lever of the

manifold valve completely and turn off the vacuum

pump.Make pumping for 15 minutes or more and check that

the compound meter indicates -76cmHg(-1X10 Pa)

Loosen and remove the cap of stop valves A and B to open

stop valve A and B completely, then fasten the cap.

Disassemble the charge hose from the service port of stop

valve A, and fasten the nut.

service port

cap

maintenance nut

hexagon holeshaftseal

Fig.7-9

2. Closing stop valve

Remove the cap and turn the valve clockwise with the

hexagon wrench.

Securely tighten the valve until the shaft contacts the

main bodyseal.

PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MFA-18HRDN1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MFA-18HRDN1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info