Bedienungsanleitung Midea MFAD-Serie (Seite 8 von 18) (Englisch)

588095

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

installation manual

NOTE

CAUTION

>30cm

>60cm

(Wall or obstacle)

Air outlet

Air inlet

Maintain channel

Side air outlet outdoor unit

Fig.6-5

6.2 Moving and installation

All the pictures in this manual are for explanation

purpose only. They may be slightly different from the air

conditioner you purchased(depend on model).The actual

shape shall prevail.

NOTE

All the pictures in this manual are for explanation

purpose only. They may be slightly different from the air

conditioner you purchased(depend on model).The actual

shape shall prevail.

Since the gravity center of the unit is not at its physical

center, so please be careful when lifting it with a sling.

Never hold the inlet of the outdoor unit to prevent it from

deforming.

Do not touch the fan with hands or other objects.

Do not lean it more than 45, and do not lay it sidelong.

Make concrete foundation accoding to the sepecif-ications of

the outdoor units.(Refer to Fig.6-6)

Fasten the feet of this unit with bolts firmly to prevent it from

collapsing in case of earthquake or strong wind.(Refer to

Fig.6-6)

7. INSTALL THE CONNECTING PIPE

Check whether the height drop between the indoor unit and

outdoor unit, the length of refrigerant pipe, and the number of

the bends meet the following requirements:

All field piping must be provided by a licensed

refrigeration technician and must comply with the

relevant local and national codes.

Do not let air, dust, or other impurities fall in the pipe

system during the time of installation.

The connecting pipe should not be installed until the

indoor and outdoor units have been fixed already.

Keep the connecting pipe dry, and do not let moisture in

during installation.

Execute heat insulation work completely on both sides

of the gas piping and the liquid piping. Otherwise, this

can sometimes result in water leakage.

The Procedure of Connecting Pipes

7.1

Table 7-1

Capacity(Btu/h)

The max height drop

The length of refrigerant pipe

The number of bends

12000

Less than 10m

Less than 5

16000~18000

10m

Less than 20m

Less than 8

Fig.6-6

Fix with bolt

CAUTION

Drill a hole in the wall (suitable just for the size of the wall

conduit), then set on the fittings such as the wall conduit and

its cover.

Bind the connecting pipe and the cables together tightly with

binding tapes.

Pass the bound connecting pipe through the wall conduct

from outside. Be careful of the pipe allocation to do on

damage to the tubing.

Connect the pipes. Refer to "How to Connect the pipes" for

details.

Expel the air with a vacuum pump. Refer to "How to expel the

air with a vacuum pump" for details.

open the stop values of the outdoor unit to make the

refrigerant pipe connecting the indoor unit with the outdoor

unit in fluent flow.

Check the leakage. Check all the joints with the leak detector

or soap water.

Cover the joints of the connecting pipe with the soundproof /

insulating sheath (fittings), and bind it well with the tapes to

prevent leakage.

Be sure to with insulating materials cover all the exposed

parts of the flare pipe joints and refrigerant pipe on the

liquid-side and the gas-side. Ensure that there is no gap

between them.

Incomplete insulation may cause water condensation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midea MFAD-Serie Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midea MFAD-Serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info