1. Determine hole positions according
side of the installation plate.
by measuring the distance as
2. Dirll the piping plate 65mm hole-core drill.
3. Drill the piping hole
hole should be slightly slanted
4. Always take
grid,metal plate or the like.
INST
ROOM AIR C
(Split W
DRILL A HOLE
INSTALLA
2
1
I
N
D
O
O
R
U
N
I
T
Please
Be sure to follow all
This symbol
This symbol
1) This equipment must be grounded and installed with ground leakage current breaker. It may
electrical shock if grounding is not perfect.
2) Do not install the unit at place where leakage of flammable gas may occur. In
accumulates at surrounding of the unit, it may cause fire.
3) Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water
may enter the room and damage the furniture.
1) Install according to this installation instructions strictly. If
leakage, electrical shock,or fire.
2) Use the included accessories
to fall, water leakage, electrical shock,or fire.
3) Install at a strong and firm location which is able to withstand the set
enough or installation is not properly done, the set will drop and cause injury.
4) For electrical work, follow the local national wiring standard, regulation and this
An independent circuit and single outlet must be used. If electrical circuit capacity is not enough or
defect found in electrical work, it will cause electrical shock,or fire.
5) Use the specified cable and connect tightly and clamp the cable so that n
on the terminal. If connection or fixing is not perfect, it will cause heat-up or fire at the connection.
6) Wiring routing must be properly arranged so that control board cover is fixed
cover is not fixed perfectly, it will fire or electrical shock.
7) When carrying out piping connection, take care not to let air substances
refrigerant go into refrigeration cycle. Otherwise, it will cause lower capacity,abnormal high pressure
in the refrigeration cycle, explosion and injury.
8) Do not modify the length of the power supply cord or use of extension
single outlet with other electrical appliances. Otherwise, it will cause fire or electrical shock.
SAFETY PRECAUTIONS
CAUTION
WARNING
CAU
WARNING
Please read this installation manual carefully before operating the unit to ensure correct installation.
If the power cord is damaged, replacement work shall be performed by authorised personnel only.
Installation work must be performed in accordance with the national wiring standards by authorised
personnel only.
Contact an authorized service technician for repair, maintenance and installation of this unit.
This appliance is not intended for use by persons(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by persons responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
All the pictures in the instructions are for explanation purposes only
The design and specifications are subject to change without prior notice for product improvement.
Consult with the sales agency or manufacturer for details.
There should not be any
near the unit.
There should not be any
air circulation.
A place where
A place where
A place where
consideration.
Do not install the unit
Ensure the spaces indicated by
wall,ceiling,fence or other obstacles.
There should not be any
sunlight prevention should be taken
Outdoor unit
mm(WxHxD)
A(mm) B(mm)
530
290
560
549
640
335
325
404
481
549
276
276
Mounting
670x540x265
780x540x250
760x590x285
845x700x320
810x558x310
940x810x375
Indoor
Outdoor
If an awning is built
direct sunsight or rain,be careful
radiation from the condenser is
There should not be any
could be affected by hot
Keep the spaces indicated by
ceiling, fence or other obstacles.
Do not place any obstacles
a short circuit of the
Anchor the outdoor unit with 10 or
8 tightly and horizontally on a
Settlement of outdoor
NOTE: The outdoor unit you purchase
of the following. Install the
dimension as indicated in the
A
W
B
D
Air
Air
Air
INSTALLA
CONNECT THE CABLE
3
,
Ter
Connect the
Before performing any electrical work,
1. The inside and outside
2. The indoor power cord
interconnected cord type is H07RN-F
3. Lift the indoor unit
4. Ensure the colour of
respectively.
5. Wrap those cables not
any electrical components. Secure the
NOTE:
Electronic box
cover
Front Panel
To outdo
Model A Model B
To outdo
L(1)
2(N)
S
1
W
2(N)
S
1(L)
1
2
3
4
5
7
8
9
10
6
Installation Plate
Clip Anchor
Self-tapping Screw
Seal(For cooling & heating models
Drain Joint(For cooling & heating
Connecting
pipe
Assembly
Liquid
Gas
Remote controller
Self-tapping Screw
6.35
9.52
9.52
12.7
16
Parts you
size diffe
Consult the
size.
1
5-8(depending on
5-8(depending on
1
1
1
2
1
1
Except the above parts provided,the
purchase.
Remote controller holder
ACCESSORIES
Number
Name of Accessories
Qty
NOTE:
optional
parts
SELECT THE BEST
NOTE: If used as MONO unit, for the standby control needs, the cross section area of cable connected
to L(1)/W, 1/1(L), 2(N) must be sufficient for the maximum system current. The maximum system current
is equal to the sum of indoor unit and outdoor unit rated current. If used as MULTI unit, L(1)/W on the
terminal block does not need to be connected.
4
CONNECTIVE PIPE AND
1. Run the drain hos
Do not instal
in wrong figu
2. When conne
insulate the connecting pa
drain hose w
the drain hos
Draina
Right
Wrong
Correct ori
of Inst
1. Fit the installation plate
structural parts of the wall
around the installation plate.
2. If the wall is
or the like, drill five
diameter holes in the wall.
clip anchor for appropriate mounting
screws.
3. Fit the installation plate
with five or eight type
Mount the Installation Plate and
holes in the wall according
structure and corresponding mounting
points on the installation plate.
installation plate providedwith the
machine differ from appliance
to appliance.(Dimensions are in
mm unless otherwise stated)
NOTE:
NOTE:
"
"
Installation Plate
The mounting wall is strong
to prevent it from the
4
5
4
5
2
80
120mm or
more to wall
120mm or
more to wall
120mm or
more to wall
150mm or more to ceiling
150mm or more to ceiling
Left rear side
refrigerant
pipe hole 65
3
6
.
5
835
140
110
Left rear side
refrigerant
pipe hole 65
Right rear side
refrigerant
pipe hole 65
Right rear side
refrigerant
pipe hole 65
Indoor unit outline
Indoor unit outline
120mm or
more to wall
120mm or
more to wall
Indoor unit outline
990
31
5
135
260
150mm or more to ceiling
Left rear side
refrigerant
pipe hole 65
Right rear side
refrigerant pipe
hole 65
Model C
Model B
Model A
120mm or
more to wall
45
45
3
6
.
5
750
180
110
2
8
0
202000192486 CS159I1-BP11M(L)
Air freshening filter(used to install
Electric safety regulations for the
1. If there is serious
the air conditioner and explain
2. Power voltage should be
3. The surge protector and main power
be installed in power circuit. Ensure the
4. The appliance shall beDo not operate your air
conditioner in a wet room
5. An all-pole
current that may exceed 10mA,
current not exceeding 30mA, and
with the wiring rules.
6. For the unit adopts
materials.
7. According to
unit to connect the wire.
8. All wiring
skilled
9. An individual
available. See the following table for suggested wire sizes
Minimum cross-sectional area
Rated cu
of appliance
(A)
>3 and 6
>6 and 10
>10 and 16
>16 and 25
>25 and 32
>32 and 40
Nominal cross
area
(mm2)
0.75
1
1.5
2.5
4
6
Electrical w
The wire siz
interconnected wire and the cu
the fuse or sw
maximum current in
nameplate which loc
panel of the u
nameplate before se
fuse or swit
The controller of the air co
designed with a fuse pr
under abnormal con
specifications of the fu
the circuit b
T5A/250VAC, etc.
NOTE:
