Bedienungsanleitung Midland ALAN 199 (Seite 13 von 34) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

543209

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

8 | Alan 199 Instruction Guide Alan 199 Instruction Guide | 9

just stops. Now, when a signal is present, you will hear it, but will not be di-

sturbed by noise on the channel between signals. When properly set, the

Squelch keeps the receiver “dead” until a signal comes in on that channel.

However, do not set the Squelch too high, or weak signals will not be able

to open the Squelch circuit. To receive very weak signals, it is best to leave

Squelch set to the minimum position by rotating the control maximum

counterclockwise. The Squelch circuit in your transceiver is an advanced

design. It uses an operational amp IC to accomplish a hysteresis action.

The result is that when you set the Squelch for a precise signal level, if

that signal level increases or decreases in strength, the Squelch circuit will

follow this change. With conventional Squelch circuit, often a signal which

changes strength get “chopped” by the Squelch circuit and you lose a por-

tion of the message. With a hysteresis Squelch, you get it all.

To Transmit:

1. Select the desired channel.

2. Press the push-to talk button on the microphone and hold it an an-

gle about 5-7 cm from your mouth and speak in a normal voice.

3. To receive, release the push-to-talk button. Be sure the mic plug is

ﬁrmly connected to the jack.

NOTE: shouting into the mic will not increase your power or signal. An in-

ternal circuit automatically sets the mic signal for maximum modulation,

so speak loudly will give no advantage.

PRIORITY CHANNELS (CH 9-19)

Alan 199 comes with an emergency selector that permits the immediate

activation of channels 9 or 19. The former (CH9) is used for emergency

communications only, while with the latter (CH19) you can ask for traﬃc

information, etc.

By moving this knob to the central position, the last channel selected will

be activated.

REMOTE SPEAKER OPERATION

A 4 Ohm speaker, rated at 3-10 watts, should be used for this function.

Plug the speaker into the EXT SPKR jack at the rear of the Transceiver.

When the external speaker is plugged in, the internal speaker is discon-

nected. You can now monitor all incoming signals through your remote

speaker.

BASE STATION ANTENNA

While your Transceiver is designed for mobile opera-

tion, you might wish to use it as a base station unit,

in conjunction with a 12,6 Vdc ± 10% 2 A DC power

supply. If you decide to use your Transceiver as a base

station, choose an antenna designed to operate most

eﬃciently as a base station antenna. For example, the

1/2 wave antenna is a high-eﬃciency radiator with

omnidirectional characteristics. It performs as well in

most applications as does the ground plane. You can

use this type of antenna for medium-long range com-

munications.

USING YOUR TRANSCEIVER

Do not transmit without a suitable antenna or 50 Ohm load connected to

the antenna connector.

To receive:

1. Check that the red wire is properly connected to a source of 12,6 V

± 10%.

2. Make sure that the antenna and the microphone are attached.

3. The emergency knob must be set to the central position.

4. Select the transmitting power.

5. Set the Squelch control to maximum counterclockwise position.

6. Turn on the unit by rotating the VOLUME control clockwise.

7. Set channel selector to the desired channel.

8. Adjust VOLUME for a suitable listening level.

9. Adjust Squelch to cut out annoying background noise when no si-

gnal is being received.

To do this, set the Channel Selector to a channel where no signals are pre-

sent or wait until signals cease on your channel. Then, rotate the Squelch

control in a clockwise direction to the point where the background noise

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland ALAN 199 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info