Bedienungsanleitung Midland ALAN HM06 (Seite 13 von 20) (Englisch)

738665

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English

5.7 Transmission

1) Remove the microphone from the support.

2) Verify that the channel is free (to prevent potential interference)

and check that the status LED

[9] on the right of the display is

off.

3) Press and hold down the palm-sized microphone transmission

key

(PTT). The status LED turns red.

4) Speak normally at a distance of 5-10cm from the microphone.

5) Release the

PTT key at the end of the call making sure that the

status LED switches off.

6) At the end of the conversation, place the microphone back onto

its support.

2 StarttalkingonlyafterpressingthePPTkeyandreleaseitonly

aftertheconversationhasended,otherwisethetransmissionof

themessagemaybeincomplete.

2 Donotshout!Shoutingdoesnotincreasethetransmissiondis-

tancebutaffectsthequalityofthesignalreceived.

2 Transceiverscannotgenerallybeusedtolistenandtalksimulta-

neously.Forthisreason,youwillnotbeabletotalkwhenothers

aretalking.Itisthereforeadvisabletotimeyourmessagessothat

theyarenottoolong.

2 For information on how to transmit correctly, see the following

paragraphs.

5.7.a Maximum Time Out Timer (TOT)

The radio has a programmed Time Out Timer that automatically

enables the reception mode if the speaker's message exceeds a

specictimelimit.Thesettingofthistimercanbeconguredduring

the programming phase. If this occurs, release the transmission key

and wait a few seconds to allow the radio transmission feature to be

automatically reset. For additional information, contact the radio link

provider or your local dealer.

2 Thissettingcannotbechangedbytheuser.Formoreinformation,

contacttheradiolinkprovider.

5.7.b Blocking transmission when the channel is busy (BCLO)

If enabled, this feature prevents the transmission of outgoing signals

if the channel is busy. In this case the use of the

PTT key has no

effect.

Depending on programming, the BCLO feature can be enabled for all

signalsandforsignalswithaspecicCTCSS/DCScode/tone.

2 Thissettingcannotbechangedbytheuser.Foradditionalinfor-

mation,contacttheradiolinkprovider.

5.7.c Selecting the transmission strength

Thetransceivercantransmitwiththetransmissionstrengthscong

ured during the programming phase for each channel. The red LED HI

indicates that the following strength has been selected:

• On - High strength

• Off - Low strength

Tochangethestrengthofaspecicchannel,selectitandpressthe

F key (or ) linked to this feature. The red HI LEDconrmsthatthe

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland ALAN HM06 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info