Bedienungsanleitung Midland Alan HP 406 (Seite 40 von 146) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

738663

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

12 Basic operations

5.5 Monitor

The MON (monitor) button is mainly useful for two purposes:

• If the channel you have tuned has been programmed in the Open

Traffic mode, briefly pressing the MON button temporarily disables

the squelch in order to allow you the reception of extremely weak

signals that can’t steadily open the squelch and are therefore recei-

ved “chopped”.

• If the channel you have tuned has been programmed with

CTCSS/DCS and/or Selective Call, a brief pressure of the MON but-

ton temporarily disables the CTCSS/DCS and/or Selective Call to

allow you to monitor all the communications on the tuned channel,

even the ones that are not belonging to your network. Practically, you

are able to temporarily receive in Open Traffic just briefly pressing the

MON button.

In any case, if the MON button is enabled on your transceiver, press

it briefly to temporarily monitor the signals on the tuned channel and

repeat this operation to return to the normal condition.

 Every time the MON button is pressed, a high or low acoustic tone will

be produced to notify respectively the monitor function enabled (open

squelch or disabled CSCSS/selective call) or disabled (closed squelch

or enabled CSCSS/selective call)

 Depending on the programming, the MON button could not be acti-

ve or work in order to disable the CTCSS/DCS only or the selective

call only. Please refer to your dealer/radio network manager for details.

5.6 Transmission

To transmit please follow this procedure:

1) Ensure that the channel is not busy (otherwise you will create an inter-

ference), verifying that the status LED is not glowing green or amber.

If the channel is not free, please wait until that condition (LED turned

off)

2) Keep pressed the PTT button and verify that the status LED is glo-

wing red to show that you are transmitting.

3) Speak with a normal voice level at approximately 5-10 cm from the

microphone.

4) When your message is over, release the PTT button ensuring that the

status LED is turned off.

 Don’t shout! It won’t increase the distance range, but rather will make

you heard distorted.

 Don’t release the PTT button before your message is over or start tal-

king before pressing it, otherwise your message will be “chopped”.”

 A handheld radio doesn’t normally allow to talk and receive simulta-

neously, for this reason make your messages with a reasonable time.

When you are talking, the other parties can’t do that, so don’t occupy

too much the channel.

 In order to transmit properly, please also see the following paragraphs.

5.6.a Time-out Transmission Timer (TOT)

The radio might be programmed with the internal TOT timer (Time Out

Timer) which automatically put your radio in reception if you talk too long

(after a preset time). In this case release the PTT button and wait for few

seconds: the radio TX features will be automatically restored. Ask the

network responsible or your dealer for further details.

English

ISTR106_int 26-09-2003 9:47 Pagina 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland Alan HP 406 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info