Bedienungsanleitung Midland Alan HP106 (Seite 43 von 146) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

738662

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

Advanced operations 15

7 Advanced operations

In this section we’ll describe some advanced operations which you can

do with your handheld transceiver.

7.1 Channel Scanning

If you have more than one channel programmed, your ALAN

HP106/HP406 can scan them; in other words it can repeatedly switch

through all the programmed channels cyclically and automatically stop

when a signal is detected on one of them. During the scanning, only the

channels belonging to a specific scanning list (defined by the set-up) are

monitored. If a valid signal is received during the scanning, the scanning

stops and the communication is audible through the speaker. When the

signal is over, the scanning automatically restarts.

If the CTCSS/DCS or the selective call have been previously program-

med, the device could be set-up to stop only if the received signals con-

tain the correct signaling.

7.1.a Enabling/disabling scanning

To enable the scanning:

1) Turn off the device

2) Turn on the device keeping the MON + FUNC button pressed. A high

beep (after the acoustic tone of power-on confirmation stated in the

paragraph 5.1) notifies that the scanning is activated, and the status

LED will slowly blink amber.

 During scanning the channel selector knob becomes invalid.

 If the Scan List is empty, an error tone will be heard when you try to

activate the scan and the radio will not start the Scan Mode.

Obviously, at least two channels must be entered in the Scan List for

the unit to be put in the SCAN Mode.

 If the PTT button is pressed during the channel scanning, this one will

stop and the radio will transmit on the first vacant channel, then the

unit will automatically resume scanning.

To stop the scanning, repeat the above procedure from step 1. A low

beep is produced and the scanning will stop.

7.1.b Priority Channel

Depending on the transceiver’s programming, one of the scanning list

channels could have been assigned as Priority Channel. The scanning

will monitor the priority channel more frequently.

The programming could has been also set-up to allow you to decide,

from time to time, which is the channel to assign as priority. For informa-

tion please contact your dealer/radio network manager.

To assign a priority channel (if previously enabled by the programming):

1) Ensure that the scanning is not active.

2) Before starting the scan mode, select the desired channel using the

channel selector.

3) Start the channel scanning as described in paragraph 7.1.a. The

channel previously selected by the channel selector will be scanned

more frequently.

 Once the scanning is started, if you wish to change the priority chan-

nel, you need to disable the scanning. Therefore it is not sufficient to

turn-off the device, rotate the channel selector, and switch it on again.

 Depending on the programming, on the priority channel could also be

set the busy channel lock out function (BCLO) or other conditions (i.e.

English

ISTR106_int 26-09-2003 9:47 Pagina 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland Alan HP106 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info