Bedienungsanleitung Midland BT NEXT CONFERENCE (Seite 31 von 118) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579651

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

30 - Midland BT Next

Back to factory setting

Sometimes you may nd it necessary to go back to the factory setting, to reset all

the changes/setup already made and have a “clean” unit.

To perform this operation you must rst enter the setup mode:

› Turn o the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down all the three buttons “Forward”-

“Middle”-“Rear” for 3 seconds. The Blue Light will be lit on for 1 sec and than

back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BT

Next C..

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX

activation is inuenced by the helmet type, the background noise and therefore

by the speed.

For optimum results, it is possible to choose one of the following four microphone

sensitivity levels: high, medium, low and very low. The default setting of BT Next

C. is “low”. It is also possible to disable the VOX feature in order to activate the

Intercom and phone call answering features in manual mode only.

Adjusting the sensitivity of the (VOX)

To perform this operation you must rst enter the setup mode:

1. Turn o the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

3. Your BT Next C. is now in “Set up mode”.

4. Press the “Rear” button shortly and the red light changes to a steady blue.

5. Now, press “Volume +” or “Volume -“ to increase or reduce sensitivity. Every

time you press the Volume buttons the RED light will ash for conrmation.

When you reach the end of the upper and lower limit, the RED light will not

ash.

6. Press again the “Backward” button shortly; the Blue light will ash several

times, in order to let you know the selected sensitivity:

One ash = VOX disabled

Twice = low sensitivity

3 times= medium sensitivity

4 times= high sensitivity (default setting)

5 times = Very high sensitivity

The light indicator is now back to steady RED (“Set up mode”) and the

changes are conrmed

7. If needed, you can adjust again the sensitivity repeating the steps from point

1, otherwise exit the Setting mode by double clicking the “Middle” button.

Once the red light turns o, the blue led starts blinking. Now you can use your

BT Next C..

Disabling the VOX feature (Intercom and telephone)

Follow all the procedure described in the previous steps and choose the option of

only one ash (VOX disabled).

Attention! If you disable the VOX feature, you will be able to answer incoming phone

calls only by pressing the “Forward” button.

Wired connection always in background

This feature let you keep the wired connection always on, even when the phone

or the intercom is open. This feature can be useful when you connect a PMR446

transceiver.

By default this option is on.

Disabling:

› Enter the “Setup” mode:

› Turn o the unit

› Press and hold down the “Middle” button about 3 sec., until the Red light is

on permanently.

› Press the “Forward” and “Middle” button together for 3 seconds. The blue LED

will ash three times.

› Double click on the “Middle” button to exit the “Setup” mode and use the BT

Next C..

Enabling: Follow the same procedure up described; now the blue LED will ash

once. To exit the “Setup” mode, double click the “Middle” button.

Setup and Firmware update

It is possible to congure and update the rmware of your BT Next C. using the

USB connection to your PC. On the Midland web site www.midlandeurope.com in

the BT Next C. page you can nd the PC software and the new rmware updates

if available.

ATTENTION DO NOT CONNNECT THE UNIT TO THE PC BEFORE you DOWNLOAD AND

INSTALL THE SOFTWARE

Use at your own risk

The use of the device will impair your ability to hear other sounds and others

around you.

Listening to music or speaking on a telephone may prevent you from hearing

others around you and distract you from riding safely. The use of such device

while riding may endanger you and others, and its use, in some areas, could not

be allowed.

Using this device at a high volume may result in permanent hearing loss.

If you experience ringing in your ear or any other hearing related pain, reduce the

volume or discontinue using this device. With continued use at high volume, your

ears may become accustomed to the sound level, which may result in permanent

damage to your hearing.

Please use this device at a safe volume level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BT NEXT CONFERENCE Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info