Bedienungsanleitung Midland BTX2 FM (Seite 23 von 88) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

579660

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

22 - Midland BTX2 FM

The volume buttons (Vol + and Vol -) cannot be used to adjust the volume of the wired

audio source. The AGC system with automatically increase the volume on higher speed.

Attention: never set the volume of the MP3 Player to the maximum possible. Normally the

best level is about the 70% of the maximum.

Hint: We recommend that you perform a few tests adjusting the volume of your iPod/

MP3 player so at the normal speed the Headset volume is suited to your needs. The

AGC system will automatically increase the volume on higher speed. Make a note to

remember this setting for future trips.

Enabling/disabling the wired input

If needed the wired input can be enabled or disabled:

Enabling/Disabling: Make a Long press on the “Middle” and “Forward” button (you

will hear one audio beep tone for enabling conﬁrmation and two audio beep tone for

disabling).

Using a PMR446 transceiver with the cable connection

In order to connect the transceiver to your Midland BTX2 FM, you need to purchase the

speciﬁc 2.5mm plug AUX cable, sold separately. S

ome manufacturers radios use a diﬀerent pin conﬁguration, so we recommend that

you ask your dealer as to which cable is best suited to your needs

The cable connected to the transceiver normally has also a PTT button that can be pla-

ced on the handlebar of your bike or held in your hand (If you are the passanger rider).

To communicate via the attached radio, press the PTT button to speak and release it to

listen. It is not possible to talk and listen simultaneously.

Adjust the volume of the transceiver to your needs, remembering that the volume

adjustment is controlled by the automatic AGC system and that it will therefore be

automatically increased in relation to background noise.

If you wish to use a PMR446 transceiver for group communications and simultaneously

maintain the Intercom feature enabled between two or more BTX2 FM devices, you

must remember that every time you talk to communicate with the PMR 446 transcei-

ver (pressing the PTT button), you will also activate the intercom of the BTX2 FM to the

unit connected to the “Middle” button (thanks to the VOX feature).

To avoid the Intercom activation when you speak on the PMR446, you can decide to pair

the BTX2 FM unit on the “Backward” or “Forward” (where the VOX is not active) or if you

still want to use the “Middle” button, you must disable the VOX feature, as explained

in the previous section.

Attention! If you disable the VOX feature, you will only be able to answer incoming phone

calls by pressing the “Forward” button.

Setup and special conﬁgurations

Resetting all paired devices

Sometimes you may ﬁnd it necessary to delete all the pairing references stored in

the BTX2 FM unit (reset operation).

To perform this operation you must ﬁrst enter the setup mode:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down the “Volume +” and “Volume –“

buttons for 3 seconds. The Blue Light will be lit on for 1 sec and than back

to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BTX2 FM.

This procedure deletes all the paired Bluetooth devices stored in the memory and

it is therefore possible to start a new “clean” pairing session.

Back to factory setting

Sometimes you may ﬁnd it necessary to go back to the factory setting, to reset all

the changes/setup already made and have a “clean” unit.

To perform this operation you must ﬁrst enter the setup mode:

› Turn oﬀ the unit

› Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

› Than simultaneously press and hold down all the three buttons “Forward”-

“Middle”-“Backward” for 3 seconds. The Blue Light will be lit on for 1 sec and

than back to steady RED.

› Double click on the “Middle” button to exit the “Setup” mode and use the BTX2 FM.

Adjusting/ Disabling the VOX feature (Intercom and telephone)

The Intercom feature can be enabled both manually and vocally (VOX). The VOX

activation is inﬂuenced by the background noise and therefore by the speed.

For optimum results, it is possible to choose one of the following four microphone

sensitivity levels: high, medium, low and very low. The default setting of BTX2

FM is “low”. It is also possible to disable the VOX feature in order to activate the

Intercom and phone call answering features in manual mode only.

Adjusting the sensitivity of the microphone (VOX)

To perform this operation you must ﬁrst enter the setup mode:

1. Turn oﬀ the unit

2. Press and hold down the “Middle” button about 7 sec., until the Red light is

on permanently.

3. Your BTX2 FM is now in “Set up mode”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland BTX2 FM Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info