543253
5
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
5
DESCRIPTION OF THE FUNCTIONS
CT790 displays at the same time 2 frequency bands. The frequency band pointed with the arrow
is the master frequency and it is used to transmit; the other one is the vice frequency and only can
be used to receive.
To choose the desired frequency, press the A/B key.
Under Frequency mode:
the following Nine functions can be set on both Bands: frequency step, output power, squelch
level, channel bandwidth, CTCSS, DCS, Frequency shift direction, Offset frequency, and Channel
displaying mode.
Under Channel mode:
the following seven functions can be set on both Bands: invalid-Stepping transmit output power,
CTCSS, DCS, channel bandwidth, frequency step, frequency shift direction and Offset frequency.
FREQUENCY STEP (STEP) ----- MENU 1
In standby mode, press MENU + 1; the screen displays “Step
Press MENUtoenterthefunction.Pressthe▲/▼buttonstoselectthedesiredfrequencystep,
then press the MENUbuttontoconrm.ToreturntothestandbymodepressEXIT.
This transceiver has seven available frequency steps: 5.00KHz, 10.00KHz, 12.50KHz, 25.00KHz,
50.00KHz and 100KHz.
SQUELCH LEVEL (SQL-LE) ----- MENU 2
This function turns on the Squelch when the signal is strong; the Squelch will stay off when the
signal is weak. Set the same DCS codes of your group and turn on the squelch.
By setting the level too high, you may not receive the weak signals; while by setting it too low you
may receive noises or undesired signals.
NOTE:
This transceiver has ten (0~9) available levels: 0 means that the Squelch is turned on. From level
1 to level 9 you will have different levels of noises reduction. The higher is the level, the louder will
be the Squelch.
In standby mode, press MENU + 2. The screen displays “SQUELCH”.
Press MENUtoentertofunction.Pressthe▲/▼buttonstoselectthedesiredSquelchlevel,then
press MENUtoconrm.ToreturntothestandbymodepressEXIT.
Keep pressed the side Key 2 to enable the Squelch function.
POWER SAVE(SAVE) --- MENU 3
To save battery power, this function can turn off the transceiver when no signal is received.
In standby mode, press MENU + 3. The screen displays “SAVE ”.
Press MENUtoenterthefunction.Pressthe▲/▼buttonstoselectON or OFF, then press MENU
toconrm.
To return to the standby mode press EXIT.
HIGH/LOW POWER SELECTION (TXP) --- MENU 4
In frequency mode, press MENU + 4. The screen will display “TXP ”.
Press MENUtoenterthefunction.Pressthe▲/▼buttonstoselectHIGHorLOWpower,then
press MENUtoconrm.ToreturntothestandbymodepressEXIT.
Youcanchoosebetween5W(HIGH)or1W(LOW)outputpower.BypressingtheTDR key you
can switch the output power (from high to low and viceversa).
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Midland CT790 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Midland CT790

Midland CT790 Bedienungsanleitung - Deutsch - 20 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info