Bedienungsanleitung Midland Ocean (Seite 14 von 26) (Englisch)

579587

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENGLISH

1) Ensure the channel you’ve selected is not a reception-only channel

(if it is, the transmission will be disabled) and that no one else is

talking (this will appear on your display as the BUSY icon).

2) Hold down the PTT button: will appear on the display, and the

icon will indicate your relative transmission power (the number

of bars is proportional to your relative transmission power).

3) Wait a second, then speak in a normal voice, facing the transcei-

ver’s microphone at a distance of approx. 5 cm.

4) When you have completed your message, release the PTT button:

and will disappear from the display and the transceiver will

return to reception mode.

Obviously, you can only communicate with stations that are tuned

on the same channel.

If the BUSY icon appears on the display, but you don’t hear

anything, you may have accidentally turned the volume to the

minimum level.

5.5 Monitor function

The (Monitor) button is for temporarily excluding (opening) the

circuit which silences the receiver in the absence of signals (squelch)

in order to listen for extremely weak signals that can’t open the squel-

ch stably. In this mode, you avoid listening to broken communication.

To activate the monitor function, hold down the button until you

hear background noise (or else a weak signal). Release the but-

ton when you have ﬁnished listening.

If you wish to keep the squelch open for longer periods without

holding down the button, press the button for at least 5

seconds, until you hear two acoustic sounds (beeps), then release

the button. The squelch will remain open until you brieﬂy press the

button again.

5.6 Selecting transmission power

The transmission phase absorbs the most energy. To extend the bat-

tery duty, you can select low transmission power when transmitting

over short distances. To do this, brieﬂy press the HI/LO button: LOW

will appear on the display (low power is approx. 0.5 W). If you wish to

transmit or receive over long distances or with weak signals, press

the HI/LO button again: LOW will disappear and high power will be

selected (approx. 2W).

The transceiver is factory preset on high power.

5.7 Instant recall of channel 16

Channel 16 is used as the universal marine channel for emergency

communication. Your transceiver is equipped with a button that provi-

des instant access to this channel. To instantly recall channel 16, press

the ch 16 button. Channel 16 will be selected (regardless of the usage

mode selected, except for scanning). To return to the channel selected

previous to channel 16, press the ch 16 button again.

5.8 Display lighting

If environmental light is insufﬁcient for reading the display, you can

activate the backlighting for 10-second intervals by brieﬂy pressing

the button. If you wish to deactivate backlighting before the end

of this pre-set time, press the button again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Midland Ocean Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Midland Ocean

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info