713462
43
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
en
43
If you wish to fit anAirClean
Plus50,Active AirClean 50 or an
HEPA AirClean 50 filter, see “Repla-
cing one type of exhaust filter with
another”.
Close the filter grille.
Close the dust compartment lid.
Replacing the AirClean Plus 50,
Active AirClean 50 and
HEPA AirClean 50 exhaust filters
(dia. 36 + 37)
Do not use more than one exhaust fil-
ter at a time.
Open the dust compartment lid.
Lift the exhaust filter and remove it.
Insert a new exhaust filter, making it
sure it goes in properly, then press it
down into position.
If you are using exhaust filter c or d,
press the exhaust filter TimeStrip®
change indicator (dia. 15).
After approx. 10 - 15 seconds, a thin
red line will appear in the left hand side
of the display (dia. 16).
If you wish to fit anAirClean filter,
see “Replacing one type of exhaust
filter with another”.
Close the dust compartment lid.
Replacing one type of exhaust filter
with another (dia. 12)
Depending on model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters:
a AirClean
b AirClean Plus 50 (light blue)
c Active AirClean 50 (black)
d HEPA AirClean 50 (white)
Do not use more than one exhaust fil-
ter at a time.
When changing the filter, please note
1. If you wish to replace exhaust filter a
with filter b, c or d, it is essential that
you remove the filter grille before you
fit the new exhaust filter.
If you are using exhaust filter c or d,
you must also activate the exhaust
filter TimeStrip® change indicator
(dia. 15).
2. If you wish to replace exhaust filter b,
c or d with filter a it is essential that
this filter is fitted in the filter grille *
(dia. 35).
* Filter grille - see “Optional ac-
cessories”
Replacing the thread lifters
(dia. 38 + 39)
(not possible on EcoTeQ Plus floor-
heads)
The thread lifters on the suction inlet to
the floorhead can be replaced. Replace
the thread lifters if the pile has worn
down.
Lever the thread lifters from the slots.
To do so use a suitable tool, e.g. a flat
blade screwdriver.
Fit new thread lifters.
43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Miele Complete C2 EcoLine Hardfloor wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info