Bedienungsanleitung Miele Professional PT 8301 SL (Seite 22 von 54) (Englisch, Holländisch)

666799

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Electrical connection

The electrical components of this dryer comply with

IEC 335-1 and IEC 335-2-11.

The electrical connection may only be carried out by

a suitably qualified technician in accordance with

local and national safety regulations (BS 7671 in the

UK).

Please observe the wiring diagram supplied.

Please ensure that the voltage and frequency of the

dryer as quoted on the data plate comply with the

on-site supply.

Connection should be made via a suitable isolator

which complies with local and national safety

regulations and which is easily accesible for

disconnecting the dryer from the electricity supply.

Provision must be made on site to switch off all poles.

Switches with a minimum all-pole contact gap greater

than 3 mm are suitable for isolating the appliance.

These include circuit breakers, fuses and relays

(IEC/EN 60947).

If the appliance is disconnected from the electricity

supply ensure adequate measures are taken to

ensure that the appliance cannot be reconnected to

the electricity supply until all work has been carried

out.

After the dryer has been connected to the electricity

supply check the phase rotation on the incoming

power supply to the appliance.

Equipotential bonding

Equipotential bonding must be carried out if required.

Air inlet and exhaust connection

This dryer must only be used when it is connected to

a suitable ducting system. The installation site must

be adequately ventilated. See the installation

instructions supplied.

Gas connection

This work must be carried out by an authorised

person in accordance with local and national safety

regulations. This must be a Gas Safe registered

technician in the UK. See the installation instructions

supplied.

The earth lead (N) and phase conductor (L)

must be connected to the correct connectors.

Take care not to connect them the wrong way

round!

The gas group to which the dryer has been set at the

factory is given on the Gas Data label on the rear of

the dryer.

If the appliance is converted for a different gas

group, or to liquid gas, a conversion kit is required.

This is available from the the Miele Spare Parts

Department. When ordering please quote the model

and serial number of the appliance, as well as the

gas type, group and connection pressure in the

country of installation.

Please follow the installation instructions carefully. To

ensure safety, any conversion work must only be

carried out by an authorised technician, e.g. Gas

Safe registered in the UK.

Do not attempt to repair or work on gas-heated

appliances yourself. Repairs must only be carried

out by an authorised technician to ensure safety.

In the event of a fault please contact the Miele

Service Department.

After setting up and connecting the appliance,

ensure that all outer casing parts are correctly

fitted back into position.

Installation and connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Miele Professional PT 8301 SL Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info