Bedienungsanleitung Miele PT 8253 (Seite 22 von 54) (Englisch, Holländisch)

447870

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Electrical connection

The electrical components of this machine comply

with IEC 335-1 and IEC 335-2-11.

The electrical connection may only be carried out by

a suitably qualified technician in accordance with

local and national safety regulations (BS 7671 in the

UK).

Please observe the wiring diagram supplied.

Please ensure that the voltage and frequency of the

machine as quoted on the data plate comply with the

on-site supply.

Connection should be made via a suitable isolator

which complies with local and national safety regula

tions and which is easily accesible for disconnecting

the machine from the electricity supply. Provision

must be made on site to switch off all poles. Switches

with a minimum all-pole contact gap greater than 3

mm are suitable for isolating the machine. These in

clude circuit breakers, fuses and relays (IEC/EN

60947).

If the machine is disconnected from the electricity

supply ensure adequate measures are taken to

ensure that the machine cannot be reconnected to

the electricity supply until all work has been carried

out.

After the machine has been connected to the

electricity check the phase rotations on the incoming

power supply to the appliance.

Equipotential bonding

Equipotential bonding must be carried out if required.

Air inlet and exhaust connection

This tumble dryer must only be used when it is

connected to a suitable ducting system. The

installation site must be adequately ventilated. See

the installation instructions supplied.

Steam connection

Steam connection must only be carried out by an

authorised installer.

See installation instructions supplied with the

machine.

A steam valve and condensate trap are available to

order from your Miele Dealer or the Miele Spare Parts

Department.

Gas connection

This work must be carried out by an

authorised person in accordance with

local and national safety regulations.

This must be a Gas Safe registered

technician in the UK. See the

installation instructions supplied.

The earth lead (N) and phase conductor (L)

must be connected to the correct connectors.

Take care not to connect them the wrong way

round!

The gas group to which the machine has been set at

the factory is given on the Gas Data label on the rear

of the machine.

If the machine is converted for a different gas group,

or to liquid gas, a conversion kit is required. This is

available from the Spare Parts Department. When

ordering please quote the model and serial number

of the machine, as well as the gas type, group and

connection pressure in the country of installation.

Please follow the installation instructions carefully. To

ensure safety, any conversion work must only be

carried out by an authorised technician, e.g. Gas

Safe registered in the UK.

Do not attempt to repair or work on gas-heated

machines yourself. Repairs must only be carried

out by an authorised technician to ensure safety.

In the event of a fault please contact the Miele Ser-

vice Department.

After setting up and connecting the machine,

ensure that all outer casing parts are correctly fit

ted back into position.

Installation and connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Miele PT 8253 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Miele PT 8253

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info