Bedienungsanleitung Milwaukee 5262-20 (Seite 7 von 24) (Englisch, Französisch, Spanisch)

641640

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite



Core bits are useful for drilling larger holes for

conduit and pipe. MILWAUKEE Thin Wall Core

Bits have heat-treated steel bodies with durable

carbide tips. These core bits are specially designed

for fast, accurate drilling with combined hammering

and rotary action.

1. Clean and lubricate the

threads on the adapter

and core bit to make later

removal easier. Screw the

threaded end of the adapter

into the rear of the core bit.

 For core bits 1- 1/4"

and larger, push the guide

plate onto the pointed end of

the center pin. Insert the center

pin and guide plate assembly

into the core bit. Be sure the

small end of the center pin is

securely placed into the hole

in the center of the core bit.

2. Insert the adapter into the nose

of the tool as described in “In-

stalling Bits”. Set the hammer/

drill shift knob to hammering

with rotation.

3. Press the center pin firmly

against your center mark, hold

the tool rmly and pull the trigger.

 If a center pin and guide

plate are not available, use a template or notched

board to start the hole.

5. After drilling to about the depth of the core bit

teeth, remove the center pin and guide plate from

the core bit. Resume drilling.

6. To change the core bit, hold the tool upwards,

pointing it away from your body, and run it briey

in forward to loosen the core bit from the adapter.

 To make holes deeper than 3", remove the

core bit, break and remove the core. Resume drilling.

Adapter

Core

Bit

Center

Guide

Plate

Clean

and

lubricate

threads







Always allow the motor to

come to a complete stop be-

fore using the control switch.

For  (clockwise) rota-

tion, push the control switch

to the left side of the tool.

Check the direction of rotation

before use.

For  (counterclock-

wise) rotation, push the con-

trol switch to the right side of

the tool. Check direction of

rotation before use.



1. To  the tool, grasp the handle rmly and pull

the trigger.

2. To  the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To  the tool, release the trigger. Make sure

the tool comes to a complete stop before laying

the tool down.



The lock-on button holds the trigger in the ON posi-

tion for continuous full speed use.

1. To lock the trigger, hold in the lock button while

pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release.

The lock button will pop out.



Position the tool, grasp the handles rmly and pull

the trigger. Always hold the tool securely using

both handles to maintain control. This tool has

been designed to achieve top performance with

only moderate pressure. Let the tool do the work.

If the speed begins to drop off when drilling large

or deep holes, pull the bit partially out of the hole

while the tool is running to help clear dust. Do not

use water to settle the dust since it will clog the bit

utes and tend to make the bit bind in the hole. If

the bit should bind, a built-in, non-adjustable slip

clutch prevents the bit from turning. If this occurs,

stop the tool, free the bit and begin again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Milwaukee 5262-20 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info